Samsung Refrigerator RF28HFEDBSAA Parts

I noticed that the bottom of the plastic bucket was cracked even though it was less than two years old. I called Samsung and they wanted to charge me almost $200. Instead, I found the part at appliance parts pros for half that cost. Since I replaced the ice tray bucket assembly, my ice maker is working perfectly! Read more

Poped off plastics caseing inside the frigerator. Unscrewed 4 screws holding black fan inplace. Followed yellow wire to locate white sensor. Need to be careful not to break styrofoam, don't force it, it should seporate from plastic easy as long as the 4 screws are out. Swap it for the new one and button it back up. While I was in there I replaced the defrost sensor and the other sensor next to the heating rod. Also I know there is an issue with drain hole plugging up with ice so I extended the... Read more

Replaced fan motor, temperature sensor and defrost thermostat. Note: I had to replace connector on new defrost thermostat. Connector on new part did not fit mating connector in refrigerator.. spliced in old connector for new one. Read more

Poped off plastics caseing inside the frigerator. Unscrewed 4 screws holding black fan inplace. Followed yellow wire to locate white sensor. Need to be careful not to break styrofoam, don't force it, it should seporate from plastic easy as long as the 4 screws are out. Swap it for the new one and button it back up. While I was in there I replaced the defrost sensor and the other sensor next to the heating rod. Also I know there is an issue with drain hole plugging up with ice so I extended the... Read more

Repair went great thanks for your service Read more

I loosened middle hinge by the 2 screws which holds a power cord that clips together, then slid the hinge flap upward to release from the door. My bottom clip hinge was broken away from spring and the only way to attach a new hinge clip was to carefully separate the hinge flap. This can be done by squeezing the flap to see where the separation seams are. Small narrow screwdrivers along with a spatula will do without damaging the plastic. This allowed for acess to the spring which connects to a... Read more

• Frost buildup

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

Replaced broken handle support bracket (part #AP5620448) and cap (part #AP5620751). Used a phillips head screwdriver and allen wrench. Pliers also came in very handy. If replacing cap and support bracket, be sure to install cap before support bracket, otherwise you'll have trouble installing the cap. I ended up not needing to replace the fixer handle (part #AP4372038), but I'll keep it around just in case. Read more

Replaced chute gasket and ice bin. Has worked great so far. Fingers crossed. Read more

• Fridge too warm
• Doesn't shut off
• Noisy

The blower motor that circulates air through the refrigerator was broken. I had to remove all the shelving and drawers from the refrigerator. Then I had to remove the plastic light cover from the center of the fridge. Then I removed all visible screws to uncover the evaporator/radiator. I then unplugged the light bulb and motor wires. Luckily all wiring is keyed so that it can be plugged in again without error. I removed the motor by opening the motor housing. The housing has 1 screw and... Read more

I took all the items out of the refrigerator. Removed the screws that hold the cover over the evaporator motor. Than for three hours used a hair drier to remove ice. The panel was frozen on if you pull on it it will break. Soaked up all the water removed the panel and took the fan blade off. That was difficult because it looks like a regular screw head however, you need to push in that which will cause it to release the blades and than push it onto the new motor. Than replace the panel put the... Read more

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

• Light not working

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more

New filters did not fix issue and lines were clear. No need to pull fridge out, Changing this part fixed completely and took about an hour. Mostly because I did not find a good step by step to follow. FIRST: Shut off water, but leave power on for inside fridge lighting. 1. Remove two crisper drawers 2. Squeeze two white tabs just under glass shelf in middle filter housing while pulling off front filter cover (has big hole for filter in middle of it). This requires slotted screwdriver to LIGHTLY... Read more