Poulan Chainsaw Parts

Combustion engines operate because of the chambers that seal in the tiny explosions caused by fuel, air and a spark. The pistons are part of the process of taking power from those explosions, and the piston rings seal the combustion chamber so that all of the gases created remain inside of the engine's crankcase. This replacement piston ring will ensure that a chainsaw's engine can do that, as well as maintaining the right amount of oil between the piston and the cylinder wall. An OEM replacement part, this piston ring works with Craftsman and Husqvarna chainsaws, among others. It will require a wrench set, screwdriver and a pair of pliers to make the replacement. Sold individually.

Chainsaws generate a great deal of heat and friction, but the oil pump systems that keep the situation under control. They do this through the use of chainsaw bar oil poured into a reservoir. It remains in the reservoir until the throttle is engaged which then cues the pump to spray oil out of a port and smear it on the bar and chain to reduce friction and heat. The use of the oil pump is crucial, and this OEM oil pump assembly is a full replacement for times when a chainsaw is not getting adequate oil on the bar. It works with Poulan, Craftsman, Poulan Pro, and others. This project requires only wrench and screwdriver sets to perform the repair. It ships as an individual kit ready for full replacement of the original oil pump.

This part is a replacement engine pulley. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a broken, defective, or damaged engine pulley on lawn mowers.The engine pulley is what drives the equipment's transmission belt. If this pulley is worn or malfunctioning, the blades of the mower or tractor will not rotate properly, if at all. Thus, this part should be replaced in order for the equipment to function properly. It's important when working on or near an engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this engine pulley, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this engine pulley is suitable for use on several models of lawn mowers and lawn tractors manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This part is a replacement screw. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a defective or misplaced screw in a variety of lawn equipment. This screw is a high-quality piece of standard hardware with multiple different uses. Screws are essential for securing parts of the equipment, but can easily become lost, stripped, or otherwise damaged. If screws are missing, it can affect the functionality of the equipment. A Phillips head or flat head screwdriver can be used to install this screw. It's important when working on or near any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this screw is suitable for use on several models of lawn equipment manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.

This is a genuine OEM lawn and garden equipment screw that is used in various types of machines. It is a tapping screw that may have several applications depending on the exact equipment in question. A hex key screw is responsible for providing a secure hold for various components. It is made of durable metal, but also exposed to high heat and constant vibrations which can lead to wear, damage, or even breaking. The screw should always be replaced with an OEM replacement. This genuine OEM tapping screw is manufactured by Poulan. It is designed to be used in select outdoor power equipment units from the brand. It can also be used in compatible models from Paramount, Weed Eater, Jonsered, and Husqvarna. It fits trimmers, chain saws, and hedge trimmers from these brands. The tapping screw is sold individually and does not include any additional hardware or parts. A Torx screwdriver or hex key will be required to replace this tapping screw. Be sure to wear gloves when performing engine repairs and allow the machine to cool completely before starting work.

This is a replacement chainsaw retaining ring. The sprocket is commonly attached to the gear drive shaft in chainsaws with a retaining ring. If the original retaining ring becomes damaged, the chainsaw will not operate properly.Needle-nose, snap ring, or retaining ring pliers may be required to remove the old, damaged retaining ring. To install the new retaining ring, snap ring or needle-nose pliers should be placed into the small holes located on the new retaining ring. Then, slightly open the pliers to pull back the retaining ring's arms, opening up the ring center. Careful attention should be paid while opening the retaining ring to avoid overstretching. Overstretching the retaining ring would lead to the sprocket not correctly attaching to the chainsaw's gear drive shaft. Finally, with proper sizing, the retaining ring can be placed over the wheel grove, attaching the sprocket to the drive shaft.This retaining ring is an OEM part that is sourced directly from the manufacturer. This retaining ring is designed to replace damaged rings in Poulan, Poulan Pro, Husqvarna, and Craftsman chainsaws. The retaining ring is sold individually.

Carburetors mix fuel with air to ensure the engine gets just the right amount of combustion. It works when idling and when in operation, and a chainsaw carburetor requires an adapter. This reduces vibration to the carb and isolates heat to help keep the carburetor cool. This carb adapter kit will connect the carburetor to the cylinder and uses a gasket on either side that can fail and require replacement. Because plastic can be used for a carb adapter, it can crack and lead to failure. This OEM carb adapter kit is meant for Craftsman, Poulan and Husqvarna chainsaws, and will work in many different models. Replacing it will require the use of a wrench set, socket set, pliers, and screwdriver. As noted, gaskets may also be needed, but this part is sold individually and includes only the chainsaw carb adapter.

This is a chain bracket ensures the chain on the equipment remains attached and stable when the lawn tool is being used. This chain bracket is made of durable materials but over time, it can wear out or experience damage. If there is substantial damage or the chain bracket has broken, it will need to be replaced.If a replacement is needed, work gloves and a wrench set will be needed. Make sure the chainsaw is powered off and the spark plug wire has been removed from the equipment. The clutch itself will first need to be removed to get access to the chain bracket. Remove the old chain bracket using a wrench and take the new bracket and place it in the same location. The chain will interlock with it. Make sure it is tightened properly before putting the spark plug wire back on.This is a genuine OEM replacement chain bracket that is directly sourced from the manufacturer. It is sold as an individual component. The chain bracket is designed to be used with chainsaws and string trimmers manufactured by Poulan, Poulan Pro, and Craftsman.

The clutch assembly is located in the clutch drum and connected to the drive shaft of the motor. This part is what allows the engine to idle without actually driving the cutter on lawn and garden equipment. The clutch is constantly engaged, so it can wear out over time and eventually need to be replaced. It may also become damaged in a direct impact or incident. If the clutch assembly fails, this could impact the ability of the engine to idle properly or even to remain running once it's started. This replacement part can offer an exact fit for compatible engines. This OEM clutch assembly is manufactured to high standards by Poulan and is designed to be compatible with various machines from Poulan, Weed Eater, Jonsered, and Husqvarna. The clutch assembly is a replacement part for various trimmers and pruners from the brands listed above. Replacing the clutch will require a wrench, screwdriver, pliers, and socket set. Be sure to cool the engine completely and wear gloves when doing repairs on lawn and garden equipment for safety.

This is an OEM replacement chainsaw bar plate for select brands and models of chainsaws. The chainsaw bar plate is responsible for holding the chainsaw guide bar in place and providing a secure foundation to reduce vibrations, while also spacing the bar from the chassis. The plate itself can become loose over time, or can even become damaged and lead to things like oil leaks from a loose chain. If the bar plate is in disrepair or not functioning correctly, it should be replaced immediately. this genuine replacement part can provide an exact fit for compatible saws. This OEM bar plate is manufactured by Poulan and will fit a number of chainsaws from the brand Craftsman, as well as those from Husqvarna and Jonsered. This durable part is made from high-quality metal and can be replaced with only a few tools. The plate is sold individually as a single unit. Hardware is not included and will have to be purchased separately if it is required. Always wear gloves and disconnect the spark plug before beginning repairs on chainsaws.

This part can be used to replace a deteriorating or leaking oil pick-up in chainsaws. An oil pick-up is essential for a smooth-running piece of equipment, as it supplies oil to the engine. Over time, oil pick-ups can become worn, which can cause leaks and prevent the engine from receiving the necessary supply of oil to operate properly. This part is manufactured from high-quality, durable plastic and non-corrosive metal. This assembly pick-up oil tank is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement assembly pick-up oil tank fits various different models of Husqvarna and Poulan chainsaws. Please note this part is sold individually.

This replacement part is a trigger and lockout kit intended for use in chainsaws. This is a genuine replacement part made by Husqvarna. Trigger and lockout kids are situated next to the handle at the top of the appliance. This part is one method of protecting the user from anything that can be harmful when using a chainsaw. It is made of durable plastic and metal. A new trigger and lockout kit might be needed if the current one is damaged or broken in any way. It is not unusual for this part to require replacement after years of normal use. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with chainsaws made by Husqvarna.

This replacement oil tank for a pole pruner or chainsaw is an authentic OEM replacement part. The inner workings of an engine consist of many moving parts. These parts are mostly made of metal and they thrash about against each other to produce and transfer energy. Engines use oil to lubricate these parts so that they do not rub and create friction as this would cause the engine to overheat. This oil tank lets operators quickly top up their engines with oil without having to take apart the inner mechanics. Oil tanks are made of durable reinforced plastic but it is still possible to bang, dent, or even puncture them. Should this happen, oil will leak from the tank and the engine will be starved of lubrication. For safety purposes, it is important to immediately replace a broken oil tank. To do so, use a wrench to remove the old tank and install the new part with the same bolts. This oil tank is compatible with Poulan and some Husqvarna appliances, and as a high-quality replacement part, it comes sourced from its original manufacturer. This part includes an oil tank and oil tank cap but it does not include an oil line.

This authentic OEM part is a replacement momentary switch meant for a chainsaw or edge trimmer. Also known as a kill switch, a momentary switch acts as a safety measure to immediately shut off the appliance's motor. If the user begins to lose control of the appliance, they can simply hit the momentary switch and the engine will disengage even if it is not currently in the off position. This helps to prevent accidents and bodily harm. When engaged, the engine requires a five second waiting period before it can restart. Over time and through repeated use, switches can naturally become worn out. They may also be damaged if knocked against something hard on accident. Replacing this switch will require a screwdriver to access the switch located in the handle of the appliance. Once accessed, the switch can easily be replaced by detaching the wires and inserting the new part. Be sure to follow the user's manual as this process will vary depending on the appliance. This part is sourced directly from its original manufacturer and will work with Poulan and Weed Eater appliances. This part ships individually.