Poulan Chainsaw Parts

This replacement part is a line guide, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This line guide is small but aids in creating straight lines while cutting the grass in many different lawn mowers. A new line guide might be needed if the user notices the current one is not working properly. If the cutting lines of grass are not as straight as normal there might be an issue with the line guide inside of the machine. Be sure to wear working gloves while replacing this part as it is typically found near the blades of the appliance. This small part is sold as a single piece. This part is a genuine OEM part sourced directly from the manufacturer. Be sure to reference the specific owner's manual for more information on how to replace this part.

This fuse is a genuine Husqvarna part, sold individually. This fuse can be used as a replacement part in a lawn mower. The purpose of the fuse is to protect the lawn mower from exceeding the maximum electrical current of which the appliance is capable of withstanding.The fuse of a lawn mower can be blown, and if the fuse cannot be repaired, the component should be removed and replaced by this genuine OEM replacement part. Signs of a blown lawn mower fuse can include a punctured, torn, frayed or smeared wire. It is a simple replacement process that will require only basic tools to properly execute. Make sure to reference the appropriate manuals when conducting this replacement. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This fuse is compatible with the following outdoor appliance brands: Husqvarna, Poulan, Craftsman, Ryobi, and Jonsered.

This is a bellcrank ground drive intended for use with riding mowers, tractors, and trimmers. The bellcrank ground drive employs the idler pulleys when the pedal brake control shaft assembly is pressed. A new bellcrank may be needed if the original was faulty, or if it becomes significantly worn through general operation of the machinery. However, installation of a new bellcrank is relatively simple. Only a few tools will be required when replacing this item, including: a socket set, a set of pliers and a hex wrench. The removal of the mower deck will also be required. The user should refer to their owner's manual for guidance regarding their specific model.This is an OEM part sourced directly from the manufacturer. It is sold individually. The bellcrank ground drive is designed for use in Husqvarna, Poulan, Weed Eater, and Jonsered models.

This washer is used in the steering column of lawn mowers and lawn tractors. It is silver with smooth edges, and it fits bolt shoulders crafted by Husqvarna. Washers are flat pieces of steel used to prevent stripping of bolts and screws.This part is intended to be used in conjunction with a bolt shoulder and bracket deck suspension. Place the washer against the bracket deck suspension and screw the bolt shoulder through the hole in the washer. This keeps the washer in place and creates a buffer between the bolt and the bracket. Failure to use a washer will prevent the bolts from tightening appropriately and negatively impact load suspension. These washers are expertly crafted. Still, washers may need to be replaced due to rusting or corrosion. These issues, combined with regular wear and tear, can cause the washers to fail or break over time.This washer is compatible with numerous mower models and personal use tractors, including Husqvarna, Poulan, Ariens, and Craftsman. This piece fits any model produced by Husqvarna that requires part #532199162. Sold individually. This part is guaranteed, genuine Husqvarna. This is an OEM replacement part sourced directly from the manufacturer.

This is a tank cap assembly that is used on many models of chainsaws. It is located on the fuel tank and is designed to ensure all fuel stays within the container. A retainer is included with the tank cap assembly to prevent dropping the cap and allowing dirt and debris into the fuel tank. An O-ring is used to seal the cap in the proper position. Tank caps can be damaged or lost, which can lead to dirty fuel, so the part will need to be replaced.Before replacing the tank cap assembly, make sure the chainsaw is off and the engine is cool. Place the chainsaw on its side and unthread the original tank cap assembly if it is still present. Pull the retainer from the fuel cap. Replacing the cap requires no special tools, but a pair of work gloves can be helpful. Take the new tank cap assembly and place the retainer into the tank. Thread the new cap on and tighten it before use.This part is made to be compatible with Poulan and Craftsman chainsaws. This tank cap assembly is an authentic OEM part that is priced as an individual part. It is directly obtained from the manufacturer.

This replacement part is an insert transfer and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Insert transfers are small but very important to many different appliances like chainsaws. These parts reduce friction inside of the motor and piston. Without this part the engine could become damaged.A new insert transfer might be needed if the user hears noises coming from the equipment that are not normal. If there is excess heat coming from inside the appliance this might also be the cause. It is common that insert transfers become stripped overtime due to normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This is a plunger and gear assembly that provides lubricating oil to chainsaws. This part is compatible with over 125 chainsaws. Proper lubrication of the cutting chain is necessary for chainsaws as the rotation of the chain through the wood results in extreme heat and diminished ability to smoothly cut. Lubricating oil cools the chain and smooths the travel of the chain around the blade. Through continual use, the plunger and gear assembly will wear and cease to function. A sure sign of this occurs when the oil reservoir is full, but the chain is heating up and chewing rather than cutting wood. To replace the plunger and gear assembly, first, remove the chain and detach the bar. Then the clutch mechanism can be unscrewed, revealing the gear and plunger unit. Because contaminants can accrue in the reservoir and in the old assembly, it's best to discard any remaining oil safely and fill the reservoir with new oil. When replacing the gear and plunger assembly made by Jonsered, Husqvarna, and Poulan, it is best to use a genuine OEM replacement part such as this one, which is manufactured according to the specifications of the factory original.

This is a fuel filter and hose that fits several different models of chainsaw. It's located near the fuel tank and works to prevent dirt, debris, and water from entering the combustion chamber of the chainsaw. It removes the impurities that are in the fuel before any of them can reach the carburetor. If the filter is clogged, the hose is kinked, or either of the components is otherwise damaged, it will need to be replaced.A sputtering noise when starting the chainsaw could indicate that the fuel filter and hose are damaged. It can also cause difficulty starting, or uneven idling. If the problem is severe, the chainsaw may have little power while it is being used or might not turn on at all. When replacing this part, make sure the chainsaw is powered off and the spark plug has been removed. The fuel filter and hose can be removed from the fuel tank and replaced to get the chainsaw to run again.This fuel filter and hose is a genuine OEM replacement part directly sourced from the manufacturer. It comes as an individual part. It is designed to be used with compatible Craftsman and Poulan chainsaws.

This part is a replacement isolation limiter screw. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. It is intended to replace a broken, stripped or defective isolation limiter screw in chainsaws.This isolation limiter screw helps to reduce movement and secure components of the chainsaw. It is a critical component that may become stripped, corroded, misplaced, or otherwise defective over time, requiring replacement. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this isolation limiter screw, the appropriate owner's manual and equipment diagrams should be referred to. This isolation limiter screw is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with chainsaw models that have been manufactured by Husqvarna, Poulan, and other brands.

This starter cup assembly is a genuine Husqvarna part, sold individually. This starter cup assembly can be used as a replacement part in a string trimmer. The purpose of the starter cup assembly in a string trimmer is to rotate the flywheel with the purpose of powering on the small engine of the string trimmer; the starter cup assembly is a key component of the pull-start mechanism of a string trimmer.If the starter cup assembly suffers from puncturing, tearing, scraping, cracking, denting, eroding, or warping to the point of reduced efficacy, the starter cup assembly should be removed and replaced by this genuine OEM replacement part. Always unplug the appliance before performing any kind of repair or replacement.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This starter cup assembly is compatible with the following outdoor appliance brands: Husqvarna, Craftsman, Poulan, and Poulan Pro.

This genuine OEM replacement ignition module is a type of electric switch used to send signals to the ignition cable and create a spark to fire up the engine in a gas-powered chainsaw. When the ignition coil creates a high-voltage charge, it triggers the spark plugs to create a spark and ignite some fuel so the engine will start. The ignition is usually one of the first things to check if an appliance's engine does not start, after checking for fuel and then the spark plugs. If the spark plugs are fine, though, the problem is likely to do with another part of ignition, namely the ignition module. As it is located near a high-voltage region of the ignition, the switch can fry and will need to be replaced. Using a pair of pliers, a screwdriver, and a wrench set, switch out the faulty ignition module and test the engine to see if it starts. This replacement ignition module is compatible with Craftsman chainsaws and does not include any addition hardware. As a high-quality part, it comes sourced directly from the original manufacturer.

This part is a replacement choke lever. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. The intended use for this part is to properly replace a defective or broken choke lever in line trimmers.The choke lever enables the choke plate to open or close within the carburetor, which helps to power on the engine. The engine may not start if this part is faulty, so if damaged, it should be replaced. Always ensure that the equipment is completely powered off and is cooled down before attempting to start the repair process. For more accurate information on the installation of this particular choke lever, reference the owner's manual or equipment diagrams for specific instructions and part location. This is an authentic OEM part and as such is sold individually and made from durable and high-quality plastic. This choke lever can be used with a variety of line trimmer models manufactured by Husqvarna, Poulan, and other brands.

This is a genuine fuel pickup assembly that is an integral part of many models of chainsaws from major manufacturers. This component is part of the fuel system and ensures the gasoline makes it from the fuel tank to the chainsaw's carburetor. When the primer bulb is pressed, it causes air to leave the carburetor so it can be filled with fuel. The extra fuel moves back into the tank using a return line. This part is made from quality materials but can wear out or become damaged, which will require it to be replaced.Basic tools like an Allen wrench and a screwdriver may be needed to replace the broken or damaged fuel pickup assembly. A pair of work gloves is also useful for the process. Make sure the chainsaw is powered off and placed on a level surface. Disconnect the spark plug wire to prevent the engine from powering on. Disassemble the tool to gain access to the fuel pickup assembly so it can be replaced with a new component.This is an authentic OEM replacement part that is sourced directly from the manufacturer. This fuel pickup assembly is sold individually. The part is designed to be compatible with chainsaws manufactured by Craftsman, Husqvarna, and Poulan.

This genuine OEM hub spring is designed to fit select models of chainsaws. The hub spring is responsible for providing the spring action that reacts to the pull starter. This generates the power that rotates the flywheel and helps engage the engine in the starting process. The spring becomes worn and extended with regular use. Since it is metal, it may also be subject to corrosion or other environmental damages. In either case, the hub spring should always be replaced promptly if it is found to be defective or damaged in any way. This genuine hub spring can be used for a variety of chainsaws from Poulan, Husqvarna, AYP, Sears/Craftsman, Roper, Poulan Pro, and Weed Eater. This item is sold as an individual unit. Springs are under pressure and can be dangerous to replace so always use caution. Allow the engine to cool before beginning repairs and always wear gloves for any kind of engine part repairs or replacements.