1 Answer Hello Steve. You will need to check your unit and see if it is a 120 volt unit or a 240 volt unit. Then you will buy the correct icemaker assembly DA97-00258C. Hope this helps. Read More...
Jim January 06, 2012 for Model Number Samsung Refrigerator Model #RS267LAS/XAA What is part # for "tray only" on DA97-00258C ice maker?
Dave A December 21, 2011 for Model Number RS2577SL Hello--I'm only gettig 25vac at the solenoid for the ice fill as opposed to the 120vac for the working water solenoid.The ice machine switches have continuity when activated. How will replacing the ice maker with another one with switches that also work activate the test fill better than the one I have now?
1 Answer Hello Dave. The manufacture recommends replacing the icemaker assembly DA97-00258C when this issue occurs. However, if you are certain the icemaker is good, and the voltage is the problem, you will need to replace the Main Control Board DA41-00104M. Hope this helps. Read More...
Dave---A December 21, 2011 for Model Number RS2577SL Follow up on ice maker problem--As stated in my original post the water fill solenoid tests out fine.The water line isn't frozen.There seems to be a lack of connectivity/communication between the icemaker and the processor and the solenoid for ice fill.That plug has a constant voltage of 25vac and doesn't change when the test fill button is depressed on the ice maker.And to repeat The first thing I checked were the switches on the ice maker unit as that would be the start of the trouble shooting procedure.
1 Answer Hello Dave. If the valve is good, and there is voltage there, then the icemaker assembly DA97-00258C is bad and will need to be replaced. Thanks and Good Luck! Read More...
John P. September 11, 2011 for Model Number RS2534VQ Every time there has been a loss of electricity in my home, my the refrigerator side always returned back to it's origional setting of 38 degrees. However, the freezer never returns to it's origional setting of -4. Once power is restored there is blinking dash on the LCD, which I have discovered is the code for a faulty ice maker sensor. The coils completely freeze so I open the panel and allow the ice to melt. Can you please advise me as to what I need to order rectify this problem. Thank You , John Pilato
1 Answer Hi John. After power applied again it judges the freezer temp. and if it is below 41 degrees F, it is judged as a instant power failure while operating and restoring the functions @ the panel display. If it is found it is above 41degreesF, it will execute as extended power failure and Panel Display will be initilized as (automatic setting at -4f/-20c) for freezer and 37.4 F/3c for refridge. Is your ice maker working? Is the frost on the back of the freezer wall, then you need a defrost thermostat part # is DA47-10160H. The Defrost heater is part # []. The freezer thermister is part # DA32-10105R. You do not want a defrost issue which leads into a no-cool. Thank you. Read More...
Ernesto August 28, 2011 for Model Number rs2578sh The ice make just stop making ice. I check the tray is in angle position. I call tech support say press 8 seconds the button underneath. After two hour it was kind a twissted and I help to rotate something holding now it upside down position and not working at all. Is there something wrong on tray or the ice maker?
1 Answer Hi Ernesto. It is very common that the ice maker tray will have a build up of calcium and the cubes will stick and not come out. As cheap as the trays are it is a good idea to have one extra on hand always so you have another one immediately. If the ice maker is rotating and calling for ice, then the tray just needs changed. The ice maker is part # DA97-00258C. The tray is part # DA63-01453B. Thank you. Read More...
Todd June 26, 2011 for Model Number Samsung Fridge model RS256SH I replaced the ice maker on our Samsung side by side fridge model RS256SH. With the part Part Number: AP4172188. It won't cycle the ice. I can click the harvest cycle to cycyle the ice. It will dump the ice return to the up position and fill with water. Then I will hear 2 beeps from the fridge. Is there another issue with the fridge or ice maker that wouldn't allow the ice machine to run. Any advice would be great. I have had the new ice maker in for 2 weeks and won't cycle at all. The stop bar appears to be functioning fine. I had the same issue with my old ice maker that is why I bought a new one to fix the problem.
1 Answer Hi Todd. Please use this diagnosis process.Start. The condition of close on operation is subjected the freezer door. Is ice ejected? YES- What’s your selection between crushed and cubed? cubed ice. Is the cube ice ejected sufficiently?.NO .Does MICOM No. 25 turn 5V if pressing Ice S/W? YES. Does IC3 No. 18 turn 0V if pressing Ice S/W? Measure both contact terminals of RY77 after the separation of CN70, CN71 separation of CN70, CN71 connectors. YES.Does thecontact shelf of RY77 relay turn 0??ifpressing ICE S/W?YES. Main PCB is normal operated- - - Necessary to check other sections.1) Check the wire between terminals of the AUGER motor and main PCB.2) Failure of cube solenoid for itself, or bad contact of the connectors.NOExchange of Main PCB(RY77relay). NO.Does ice in the ice tray exist ?YES. 1) Check the ice-ejector S/W. 2) Check the door S/W. 3) Check the ice moving motor. 4) Check the cut of wire in the Ice moving Motor section. NO. Do you see Ice Stop on the digital panel. YES. Do you see Ice Stop on the digital panel? YES.Cancel Ice Stop, select cubed/crushed ice. NO. 1) Check the water hose for folding or fastening. 2) Check the ice-water-way and solenoid value 3) Check the wires of ice-maker. What’s your selection between crushed and cubed? Crushed ice.Is the Crushed ice extracted sufficiently? NO Does MICOM No. 25 turn 5V if pressing Ice S/W? NO .Does the voltage of IC3 No. 18 turn 0V even in the ice S/W OFF? NO. Does the contact shelf of RY77 relay turn 0?? even in the power OFF? NO Main PCB is normal.- - - Check other sections.1) Check the wire between the AUGER motor and main PCB. Crushed ice. Is the Crushed ice extracted sufficiently? YES Normal operation. NO. Does MICOM No. 25 turn 5V if pressing Ice S/W? YES. Failure of Main PCB and exchange it..Does the voltage of IC3 No. 18 turn 0V even in the ice S/W OFF? YES. Failure of Main PCB(IC3) and exchange it. Does the contact shelf of RY77 relay turn 0?? even in the power OFF? Measure both terminals of RY77contact after the separation of CN70,CN71 connectors. YES. Failure of Main PCB – exchange. (The contact terminal of RY77 relay short failure.) The Main PCB board part # is DA41-00104M. This is for a model # RS2556SH. Please double check your model # as what you supplied us. I hope this helps. Thank - you. Read More...
Manlin517 June 24, 2011 for Model Number rs2577sw I just received assy and support for icemaker but the water has not come in to fill the tray. It has been a couple of hours and still no water to fill tray. I do have water coming through to the water fountain. Any suggestions?
1 Answer Hello Manlin517. There is a test button under the bottom corner of the icemaker to run a harvest cycle. Press this button and see if the unit brings in water. If so, it should work properly. Make sure you have the icemaker turned on. Hope this helps. Read More...
Todd June 20, 2011 for Model Number AP4172188 Is the thermostat part of the unit. Just purchased a new unit and it won't cycle the ice. I can manual cycle it and it will give two beeps after it fills.
Todd June 16, 2011 for Model Number samsung fridge part AP4172188 I just purchases and replaced the ice maker. It would not produce any ice. It will fill the tray and if you hit the reset button it will cycle thru. I waited overnight and still no ice produced. What tells the machine that the ice is frozen to cycle?
1 Answer Hello Todd! The icemaker thermostat indicates the ice is frozen and it is time to dump the ice and cycle. The thermostat has to achieve a temperature of 14 dgrs. or less to close and cause the timer motor to run and cycle. Thanks! Read More...