Al March 26, 2014 for Model Number MAH4000AWW Maytag Washer Motor control part #22004046. Testing following the Drive System Phase Loss Test shows that one phase is bad. Do you have a board level schematic that would show the component parts. I would like to replace the defective component parts rather than the whole board.
1 Answer Hello Al, If we had this information available, we would get it right out to you but unfortunately, the manufacturer has never given the schematics for any of their boards out, even to their own technicians. The only way to correct this issue is by replacing the motor control WP22004046. Read More...
Wayne March 18, 2014 for Model Number MAH21PDAWW Will this part (#AP4027228 Motor Control Bd.) fit the series 14 washer.
1 Answer Hello Wayne. Yes part# [22004046] is the correct motor control board for your series. Read More...
Clay February 18, 2014 for Model Number MAH5500BWW Ser#B7103557GT Maytag Neptune washer with LR error code after wash cycle but without spinning and before rinse cycle. Went through diagnostics and the Spin test shows that the basket will spin at the different levels of test up 99. Quick Cycle test also shows that each stage of the complete wash cycle is working. I can force a spin and a rinse cycle but the basket doesn't spin as fast as it should and clothes are much too wet after. Water is draining, hose was cleaned. Door is locked. Essentially no spin and machine times out with LR code. Also, motor load test does not respond while in service mode. Is this a motor control board issue? Thanks!
1 Answer Hello Clay. Based on the information you provided, the motor is testing good. It sounds like the control board WP22004046 is bad and will need to be replaced on the unit. Read More...
Rich B January 23, 2014 for Model Number MAH4000AWQ serial #40378222WH I have a Maytag Neptune and it start making noise when it turns one way or the other. Noise is at lower movements with turning or spinning and clothes still very wet. Took off the belt to the drum and I still hear the noise so it's not the drum bearings. The motor shaft spins freely by hand turning with no noise or friction. The noise is just when it kick on and when it kicks off the shaft still spins for sometime without the noise. Could it be the control motor or is it still the motor. Again the washer drum also spins freely without noise when I have the belt off the back wheel of the drum. Motor P/N 62 702230 Model H55BMBJL-1820.
1 Answer Rich, This issue sounds like it would be caused by a faulty motor. The squeaking noise could be the bearings going bad on the motor. Read More...
Todd November 27, 2013 for Model Number MAH4000AWW Neptune washer does not go into high speed spin at spin cycle. Water pumps out fine. Tumbles left and right several times and then ends spin cycle. Door locks. Door wax motor replaced a few years ago, control board has no burnt components (replaced with wax motor). Removing connector JP4 and testing allows drum to spin at 50 rpm. Jumped unbalance switch but it still doesn't spin out. Voltage across tub displacement switches is within what I was told is an acceptable range. Tried running diagnostics included with schematic. Seem to have the newer motor/motor control board. Doesn't have the individual wires to disconnect to test each phase as detailed in diagnostics. Hate to buy motor control board if that's not the problem. Any other checks, or does it look like the motor control board? Thanks
1 Answer Hello Todd, Check the left rear strut for a micro-switch. This switch was discontinued by Maytag and if it is present on your unit you need to cut the wires to it and splice them together to eliminate the switch from the circuit. Next, make sure the two blue wires are making good connection to the front bottom switch. The next step is to check the electrical connections to the machine control board in the control panel. A lost connection is the most common failure in this model line. Read More...
Ron L September 23, 2013 for Model Number MAH4000AWW Door lock light not lit and spin cycle not working. Everything else seems to function fine. Is it the wax motor?
1 Answer Ron, You will want to check the control board in the console to make sure that the R11 resistor is not burnt. If this is the case then you would need to replace the wax motor WP22002119 and the control board WP22002989. Read More...
Joe C August 10, 2013 for Model Number MAH5500bww My Maytag washer will not fill up with cold water. Hot water works fine. I have already checked and replaced the valve & hoses. That didnt make a difference. I put the washer into servie mode and it will not fill with cold water. It fills with hot and runs through the other cycles no problem. What else could it be?
1 Answer Joe, You will want to check on the control board with the unit set for cold water fill from connector P1 Pin 4 to P8 pin 2 for 120 vac when filling. If there is not 120 vac then the control board is bad and would need to be replaced. This would be the most likely cause. Read More...
Dan August 05, 2013 for Model Number MLE2000AYW Hi, just got home from a vacation and the spin cycle tries to spin, but all the clothes are wet. I was told that I need to replace the control board. Would the motor control assembly board be the part I need? Dan
1 Answer Dan, For your description you want to make sure the door is locked. The spin enable switch WP22002162 has a "closed" circuit when the door is locked (the switch farthest to the right on the door lock assembly under the top) Then check the off balance switches and wiring WP22003302 and WP22002044 located on the front of the tub at the 1, 3 and 6 o'clock positions. If any of these switches have an "open" circuit or a loose or broken wire, the washer will not spin. If all's OK, then consider the machine control board WP22004325 located up inside the dryer cabinet. Read More...
Mary H March 10, 2013 for Model Number MAH3000AWW Need to replace control board (victim of a power outage then surge). Do I also need to replace the motor? It seems they both need to be replaced together? If so please send mean exact part number so I can get this fixed. Thank You in advance, Mary
1 Answer Hello Mary. If your motor board is bad, you will need to order and replace the kit 12002039. Read More...
Dan February 21, 2013 for Model Number mah3000aww Sometimes machine shuts off during cycle. Now the machine only runs 3 or 4 minutes before stopping, during this time it fills and empties ok but the motor won't wash or spin, even when I slowly turn the control knob the motor won't work. Drum and motor turn freely by hand.
1 Answer Hello Dan. Based on the information you provided, you need to test the motor 12002039 in the unit. If there is power to it, and it does not work, you will need to order and replace the motor kit in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...