1 Answer Hello Marcel. Unfortunately, we are unable to ship outside of the US or Puerto Rico at this time. We will need a US physical address to ship parts to. Read More...
Jerry August 17, 2016 for Model Number KSB560080 MY BLENDER SUDDENLY STARTED VISIBLY SMOKING FROM UNDER THE COUPLER ON HIGH SPEED LAST NIGHT. THE BLENDER WORKS ON ALL SPEEDS AND THE SHAFT SPINS FREELY, CW AND CCW, AND IT IS NOT LOCKED UP. IT HAS NOT SMOKED WHEN RUN BRIEFLY (5 SECONDS) ON LOWER SPEEDS BUT HAS A DISTINCTLY BURNED RUBBER OR ELECTRICAL SMELL COMING FROM THE COUPLER GAP. IS THERE A REPLACEABLE SEAL OR GASKET OR RUBBER O-RING IN THERE SOMEWHERE BETWEEN THE MOTOR AND COUPLER THAT COULD BE MALFUNCTIONING? MANY THANKS, JERRY
1 Answer Hello Jerry. It sounds like either the coupler or the motor WPW10225872 got to hot and caused the smoke. There is no rubber to cause this issue. Read More...
Dennis March 17, 2016 for Model Number k5b560ac50 I need a new couple, it looks like the one in the parts picture. It is black. will it fit mine?
1 Answer Dennis, Yes, this drive coupler [Ap450686] is the correct part number for your unit. Read More...
Ron August 07, 2015 for Model Number BHG BLBHG-DZ I need a drive coupling .... Walmart says the original mfgr is Sunbeam - I also think Oster parts may be available.
Marilyn W. January 10, 2015 for Model Number KSB3WH4 The black coupler was so chewed up that I cannot imagine what it should look like. Please advise what replacement part I need.
Waurine M. December 03, 2014 for Model Number KSB655Q0B1 I would like to know if the blender drive coupler #AP4500686 is the correct part for my kitchenaid blender? The model number to my blender is KSB655Q0B1, The serial # is W13539261.
1 Answer Hello Waurine! Yes, the kitchenaid blender drive coupler WPW10279256 is the correct replacement listed for your model. Thanks. Read More...
Virginia E. July 28, 2014 for Model Number KSB580NKO Blender Jar shows leaking on the inside lower part of the jar where it sits on the motor part. The leaking seems to be on the inside rim and not around the center where the blade attaches. I cannot see a reason for the leaking. What is my problem?
1 Answer Hello Virginia. Unfortunately the manufacturer doesn't offer a blade assembly separate from the jar assembly. You will have to purchase the jar assembly WPW10555711. Thanks! Read More...
Bobby June 18, 2014 for Model Number W10279256 I watched the video, https://www.youtube.com/watch?v=WTH3g-jVUtg, but cant get the coupler off the base. The coupler spins freely by hand, CW and CCW. If the couple did not spin freely it would be easy to get the couple off, by tapping the screwdriver engaged in the the teeth with a hammer, but it spins freely. What do you recommend to get the coupler to not spin as I tap it; otherwise it will never come off.
1 Answer Hello Bobby. You have to hit it hard enough to break the threads loose. It is common for the coupling to turn on these, but with a quick swift hit, it will break loose. Read More...
Linda February 10, 2014 for Model Number KSB560QERI I know I need the coupler but I also need the male counterpart that is on the jar can you give me the part number so I can order with the drive coupler? Thanks,Linda
1 Answer Linda, the coupler is part number WPW10279256. The part needed located at the bottom of the jar is not available separate from the jar assembly, part number WPW10555711. Thanks! Read More...
Joe February 06, 2014 for Model Number ksb560 This is a 7/8 year old mixer. The original jar lasted until last year then leaked. I ordered another one which lasted until last month, then leaked. I ordered another one from you a few weeks ago and on the second use it start leaking. I am at a loss! Can you give me any suggestions? Thanks
1 Answer Hello Joe. You need to check and see if the coupling is bad and is breaking the seal on the jars. It is very uncommon for the jars to leak as yours is doing. If you contact us, we can get you a replacement jar if you ordered it from us. Read More...