Paul N September 27, 2012 for Model Number 66516463300 None of the lights are on. Checked the fuse-good. Door latch -good. 124vac to circuit board. 3.17 vdc @ each point on the ribbon. Is this right or do I have a faulty circuit board. Thanks
1 Answer Paul, Yes, based on your post information, you have to recheck the resistance of each keypad ribbon " To test an LED function: Confirm that the LED turns on during the “Display Test”at the beginning of the Diagnostics Cycle (see Diagnostics Cycle Time Chart, NOTE 5)." If you followed the instructions Lbelled "Checking Keypad Operation" on the tech data sheet, then you will need to repalce the control board WP8564543 . Thanks Read More...
Mike September 25, 2012 for Model Number KUDP01ILBL6 My Kitchenaid dishwasher stopped working and the normal and cancel lights began flashing. When I reset the washer by shutting down breaker for 30 min +,There were no lights flashing and I could run the dishwasher with no problem. Sometimes I also reset the panel by alternatively pressing hi temp scrub - hi temp dry 2x. When the dishwasher completed its full cycle and was done the normal light stated flashing again and if I hit cancel, the cancel light began flashing too. I can make the unit work again by following my procedure above. Any thoughts on what needs to be replaced. Thank you.
1 Answer Hello Mike. Check and make sure the heating circuit is working properly and if so, you will need to order and replace the control board WP8564543 in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
John September 20, 2012 for Model Number kenmore 66517369301 Front panel does not light up, nothing on any of the buttons.Thanks
1 Answer Hello John. If there is power there, and the board does not light up, you may have a bad thermal fuse 8193762 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Lotus September 16, 2012 for Model Number KUDM01TJBT0 Ordered the AP3133651 from you and replaced. It worked for about 2-3 weeks and suddenly it stopped working. No button is working. Any suggestions?
1 Answer Hello Lotus. You need to check and make sure the ribbon cable is clean and dry and is installed properly onto the control board. If not, it will cause the issue you are having. Read More...
Jeff September 13, 2012 for Model Number gu1500xtlq3 hi. have whirlpool DW. started rinsing all by itself, then frozen control panel. replaced panel with 8564543 per your website (order #2801332 - came in 2 days - Wow!). appeared to work first night, next morning frozen panel again and tub was full of water -so it did it's own rinse cycle again. called customer service, told me to post a question on line - did it in repair forum, haven't received an answer yet. Current panel status has a blinking normal light and blinking rinse light. Can't do anything else. Please help, tired of washing dishes in the sink. :) thank you!
1 Answer Hello Jeff, A flashing light on the control panel is the indication of a stuck key. The control panel WP8534840 will require replacement. Read More...
Jeff September 12, 2012 for Model Number whirlpool gold, GU1500XTLQ3 Our dishwasher originaly started by itself and was locked in a rinse cycle, then finally crashed. I replaced the control board 8564543 (from appliancepartspros.com)and when I powered back up, it acted all funny and 1/2 the digital readout didn't work and the cancel button didn't work. Unplugged all the connections and started over...perfect! but got up this morning and once again, it's done it's own rinse cycle (water still in the bottom), two dashes shown on the display, and green lights shown on "normal" and "rinse only". Nothing responds, it's locked up. Any thoughts? thank you.
1 Answer Hello Jeff, The only thing that will cause a light to flash is a stuck key. The control panel WP8534840 needs to be replaced. Read More...
Allan August 29, 2012 for Model Number GU1500XTKQ0 How do I identify which terminal is not used? What is "P4(y)" suppose to tell me about connecting the wire?? Thank you.
1 Answer Allan, The "P4" is the number of the terminal and is usually "stamped" on the control board, just above or below the terminal. The "Y" would usually indicate the colr of the wire that attaches to the terminal on the board, in short, there would be a yellow wire attached to the P4 terminal on the control board. Based on the wiring diagram for the model number you supplied, the P4 terminal on the control board will Not have a yellow wire attached to it. Thanks Read More...
Robin V August 18, 2012 for Model Number KUDI01TJWH1 My Kitchenaid dishwasher will not start. The lights all work but unit won't start when button is pushed. You can hear/feel the button pushing, but nothing happens. The dishwasher is about 9 years old. Is it the control panel or the board that needs to be replaced or would it be better to replace the dishwasher due to the age?
1 Answer Robin, With all the lights working, we can presume the door switches and thermal fuse are OK. That leaves the keypad assembly WP8270224 or control board WP8564543, and most likely the keypad " WON’T RUN OR POWER UP - No operation - No keypad response - No LEDs or display > Loose connections in dishwasher power up circuit or between keypad(s) and control. > Check resistance of all connections in power up circuit to control. Check connections between keypad(s) and control. " Thanks Read More...
Lotus August 17, 2012 for Model Number KUDM01TJBT0 No button on Kitchenaid dW KUDM01TJBT0 was working accept Heavy. Cancel/Drain button used to work and then stopped after couple of days. Ordered the electronic control from you and replace. Now everything seems to work accept Drain button. Wash is working fine but no drain cycle either. Water is accumulating at bottom. Any suggestion?
1 Answer Hello Lotus. Based on the information you provided, it sounds like the control panel WP8270226 is bad and will need to be replaced. Read More...
Ugo F August 16, 2012 for Model Number kitchenaid kudr01tjbt0 when i select a cycle the light lights up but when i push the start button nothing happens. the stop and drain does work. i check the switch and the fuse and they are ok. what can it be. i looked at the control Bord and looks good not burnout. thanks in advance
1 Answer Ugo, You want to test or replace the control panel / keypad assembly WP8270229. Based on your post description, one or more of the keypads has failed. Thanks Read More...