Tony July 07, 2012 for Model Number part number WPL 856543, kitchen aid dishwasher Removed the wires from the original control board. I installed the microtemp piece onto the new board. I don't know which connector goes where (the white and black). When looking at the mounted piece which piece goes on the right? Thanks!
1 Answer Hello Tony, If you look closely at the board, the wire colors are typed on there. GY is grey, W-R is white with a red trace, BU is blue, Y is yellow and so forth. Let us know if we can assist you further. Read More...
Harvey July 03, 2012 for Model Number KUDIO1FLSS2 Will run for 30 sec. some times clean light flashes 7 times. Thanks.
1 Answer Hello Harvey. Test the heater and the high limit thermostat. They should read closed for continuity. If they both test good, replace the control board in the unit. To reset the system, you will press Heated dry, Normal, Heated dry, Normal, Heated dry, Normal, when the unit is in stand by mode. It should start and run. Let it complete the cycle. The code should be cleared. Read More...
Jim B. June 29, 2012 for Model Number KUDI01ILBS6 When I select the type wash ( heavy, normal, rinse) the light will come on but when I push the start button nothing happens. I can cancel and the pump will run for a couple of minutes. I have tried entering the codes and all of the lights will come on for a couple of seconds. I can hear clicking a couple of times in the control area, then it will go into the rinse cycle. After the rinse cycle it will stop running and all lights go off. Is this the control module or the selector buttons that have failed? Thanks Jim
1 Answer Hello Jim. Based on the information you provided, the control panel WP8531816 is bad and will need to be replaced on the unit. Read More...
John June 28, 2012 for Model Number kud101flbl3 Clean light is blinking. When you turn on, machine works for 5 minutes then shuts down.
1 Answer Hello John. If the unit runs for 5 minutes and then stops, it sounds like the control board WP8564543 is bad and needs to be replaced in the unit. Read More...
Shuja June 22, 2012 for Model Number KUDI01ILWH6 My original board was 8564542 and replacement part is 8564543. I need instructions on how to wire this new part.
1 Answer Hi Shuja. Terminal P2-1 on the board connects to a Orange w/gry stripe wire. P2-2 terminal connects to a yellow w/ black stripe wire. The P2-3 wire is the brown wire to the fill valve. The P2-4 is the light blue wire to the dispenser. The P2-5 is open. The P2-6 is a blk wire w/wht stripe to the thermal cut out fuse. Then P-1 is either the digital display or the active user interface connection. The P-3 is a gray wire to the drain motor. The P-4 wire is open. The P-5 is blue wire to the motor. The P-6 is a White w/red or the blue w/red stripe going to the hi-limit thermostat. The P-7 is either a white w/violet or a blue w/violet wire going all the white neutral wire feeds. The P-8 is a tan wire to the door switch. The P-9 is a red w/blk to the motor. The P-10 is a blu w/ blk wire to the vent motor. The P-12 are 2 red wire's from the rinse aid dispenser. Thank You. Read More...
Aim June 19, 2012 for Model Number Kudio1flss2 All lights work, but won't start. I think I replaced the interface last year. There was water in the tub and I cleaned out quite a bit of debris from the filter and grinder.
1 Answer AIM, It's most likely an issue in the user interface WP8530995 and/or ribbon cable WP8524447. We're sending you some additional information that should help you out. Thanks Read More...
Stan May 23, 2012 for Model Number KUDMO1TJBT0 KitchenAid My KitchenAid dishwasher KUDMO1TJBT0 ran the wash cycle (normal), and went to rinse and heat. The rinse cycle would not stop. It would not go to Dry cycle. Had to open the door to get it to stop rinsing. I installed a new Electronic Control Board 8564543. The original board was 8528172. The new board was supposed to replace the original. Now the Normal light blinks and the Cancel light blinks and the dishwasher will not start. The blinking lights will not stop blinking even by opening the door. Had to turn off the breaker to stop the lights from blinking. What do you think is wrong? I also read other peoples questions and several times it read to turn off the power for a while and then turn the power back on to reset the control board. I tried this also and it did not change anything.
1 Answer Hello Stan. You will need to check and see if the ribbon cable has any moisture on it. If so, this issue will happen. Also, make sure the ribbon cable is installed properly in the unit. If so, you will need to replace the control panel WP8270226 in the unit. Read More...
Steve C. May 21, 2012 for Model Number KUDI01TJBL0, The washer works fine except a 70min cycle continues on for three hours regardless of the cycle you select. This would seem the likely culprut but should I be looking elsewhere IE sensors? I have a volt/Ohm meter and can check if supplied with the spec. If I replace the board, what are the odds that I am replacing the defective part? Thanks
1 Answer Hello Steve. It sounds like you may have a heating issue with the unit. You will need to check and see if the unit is heating properly. If not, you will need to test the heater and the thermostat in the unit. They should read closed for continuity. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Bob May 20, 2012 for Model Number GU1500XTLS2 Dishwasher gets stuck at interval 42. Do I need to replace the control panel?
1 Answer Hello Bob. Check and make sure the heater is working properly on the unit. If not, you may need to replace the heater 8193995 or the thermal cut-out WP661566. Both parts should read closed for continuity. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Anthony May 07, 2012 for Model Number kuds01flss0 Dishwasher I have a Kitchen Aid (kuds01flss0) dishwasher and none of the lights will light up any more. I have replaced the Control Board and the Interface card and it still does not light up. I have rechecked all the internal plugs, circuit breaker and dishwaher plug to make sure they were tight or on. Do you think it's the Electronic Board or do you have a wiring diagram so I can recheck to make sure the plugs are all in correctly.
1 Answer Hello Anthony. Based on the information you provided, it sounds like the thermal fuse 8193762 located on the control board is bad and will need to be replaced on the unit. Read More...