Mike C August 27, 2014 for Model Number KUDP02FRSS3 When I push the button for the type of wash I want, most of the time that panel will just flash. Sometimes the proper wash will light up from the adjacent pushed button and I will start the wash. It will fill with water and begin washing then it will quit. When I look at the panel after this, all of the lights on the panel are flashing and the wash will not complete.
1 Answer Mike, In most cases when there are flashing lights on the control panel of the unit, the issue would be with the control panel. You would also want to check the door switches to make sure that they are making good contact with the latch assembly. Read More...
Jay August 25, 2014 for Model Number 665.13842k601 kenmore dishwasher Dishwasher control panel lights not functioning properly. can push 'normal wash' without a response, then the start wash button and it will run normally with what appears to be random lights. runs full cycle without drying (no heater element on- typically turn it off anyway) and ends with proper 'clean' light indicator on. seems similar to prior failure that required circuit board replacement. but before buying a new board would like to know if there may be other issues to fix. thanks, Jay
1 Answer Hello Jay. Based on the information you provided, it sounds like the control panel WP8558208 is bad and will need to be replaced. Read More...
Floyd August 16, 2014 for Model Number Whirlpool GU2700XTSQ1 Replaced Chopper Asm. from your company. Now need to reset board. Need reset code.
1 Answer Hello Floyd. There is no code to reset the board. In order to reset the board, you disconnect the power for about 30 minutes. This resets the board in the unit. Read More...
Kathy August 14, 2014 for Model Number KUDM03FTSS2 The dishwasher no longer operates. None of the lights on the control panel light up. Have checked the house circuits to the unit and everything is connected and live power is going to the dishwasher. A few weeks ago, the control panel became erratic, would not let me select certain cycles. Also, the soap dispenser does not open during the cycle to release the dishwasher soap tablet.
1 Answer Hello Kathy. You will need to check the thermal fuse W10258275 in the unit and make sure it is good. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Joe July 29, 2014 for Model Number KUDS03FTSS3 My Kitchenaid Dishwasher KUDS03FTSS3 has the keypad on the top of the door. Under normal working conditions after setting the cycle and options you press the start/resume button . The start/resume led should then lite. 3 seconds are allowed for you to then close the door and the washer begins. If you do not close the door in 3 seconds the start/resume lite will blink and you will have to press the button again and close in time for it to work. MY PROBLEM is that the start/resume led never stops blinking and I dont get the 3 second delay to close the door. I have pushed the door switch to simulate a closed door and it works until I have to release it to close the door. What's your best guess?
1 Answer Joe, You will want to make sure that the door latch is making contact with the switches and if they are then the issue will be with the keypad. If you access the tech sheet behind the kickplate you will find a chart to check the keypads by. Read More...
Joe S July 10, 2014 for Model Number 6651348K900 The cycle buttons on the left side of the control panel do not respond or light up. You cannot start a wash cycle. The buttons on the right side do light up when selected. Can a part be purchased for the left side cycle panel?
1 Answer Hello Joe. The model number you provided is not working. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Nancy July 05, 2014 for Model Number KUDP02CRBL2 I have a KUDP02CRBL2 that is not working. No lights illuminate and none of the buttons work. I have checked the thermal fuse and door switch and both are ok and working. How would i know if its the main circuit board or the overlay/button board. Or is there something else I need to check or replace.
1 Answer Hello Nancy. You test for power to the main control board WPW10084141 and if it is there, you will need to replace the main board on the unit. Make sure none of the ribbon cables are damaged on the unit as well. You can check those for continuity. Read More...
Kabuki July 02, 2014 for Model Number GUI200XTLS3 My Whirlpool dishwasher is acting up. I noticed a number of lights flashing on the control panel on the door and, in fact, the dishwasher must have run because there was standing water in the unit. No one started the dishwasher. None of the buttons responded to being pressed. I could not get the "cancel" function (or any other button) to work to drain the water. I turned off the power at the breaker switch and then turned the power back on. The lights went out and I pressed "cancel" and part of the water drained before stopping and the flashing lights went on again. I turned the circuit breaker off and on again to drain the rest of the water. My problem is flashing lights, buttons that do not work and a dishwasher that doesn't work. Is this the control panel or the electronic control board? Which part(s) do I need to purchase?Thank you!
1 Answer Hello Kabuki, On model number GU1200XTLS3, you will most likely have to replace the control panel WP8534833 since the lights flashing is an indication of stuck keys. As always, you should check for lost electrical connections at the ribbon cable before ordering parts. Read More...
Jim July 02, 2014 for Model Number DU1100XTPBA The dishwasher just stop working,the pot & pan,normal,hi-tempwash binks,if i press cancel it blinks with the other 3.Can't seem to get the diagnostic procedure to work,shut power off for a while but still nothing.
1 Answer Jim, The light above the keys flashing is normally an indications that the keypad has shorted out and would need to replace the Control panel. Read More...
George B. June 15, 2014 for Model Number 911.9328810 Electric Range/Kenmore (Roper); I need an oven control. When I use your Index, it list 3 oven control modules all of which are Frigidaire parts; putting the model #in the compatabilty shows non-compatible.
1 Answer George, the replacement electronic control listed for your model is part number WB27M4. Unfortunately, this item has been discontinued with no further replacements or cross references available and our company is unaware of any other available sources. Sorry about that! Read More...