Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Start Switch by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18025032
Manufacturer Part Number: WP3395382

The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.   

Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.

Symptoms of a bad start switch include:  

  • Heating elements or tumble cycles that will not engage properly
  • Dryer fails to operate or stops mid-cycle unexpectedly
  • Control panel appears non-responsive to selections  
  • Error codes related to ignition or power delivery faults

Note: This dryer push-to-start switch has 2 terminals.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models. 

More
$50.57

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Start Switch (Part Number: OEM18025032)

Nichole for Model Number REX4625EW1

A while back I had a paperclip stuck in the dryer drum. It prevented it from turning. I got it out and it was fine. During this time, when the drum didn't move, the timer made a rrr..rrr..rrr.. noise...like it wanted to work but couldn't. However, once I removed the paperclip from the drum everything went back to normal. 6 months later. Now the dryer started stopping mid cycle sometimes, but other times it would run all the way through and the clothes would be dry. Now the timer is making that noise again on certain settings but not others (60 min. cycle but not auto timer) and when you push the button it won't do anything anymore. I can't get it to turn on at all now. Im baffled cause none of the troubleshooting guides explain any of this exactly. Thanks for the help.

1 Answer

Hello Nichole. You will want to check the thermal fuse WP3392519 and make sure it is good. It should read closed for continuity. If it is good, go to the start switch WP3395382 and make sure it is closing when the switch is pressed. If so, you will need to replace the timer WP3976568. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Read More...

1 Answer

Hi Ellen. The 2-terminal switch is an momentary switch. It really electrically don't matter which wire where on this type of switch. However you can be electrically correct by hooking the black wire to C- or common. The wht/- Or- wht/red wire to the L terminal. The diagram is not specific as to the exact lettering/numbering . Thank you.

Read More...

1 Answer

HI Ron. Does your door switch have continuity? If not, Replace it with part # W10820036. If so then I would replace the thermal fuse(located on the blower hsg.). This part # is WP3392519.Check and make sure you have 240 volts coming to the dryer. Check and make sure the unit is not set to Air Fluff. Also check the heater and thermal fuses and see if they are good. You can test these with a multi-meter MA-DM1. They should read closed for continuity. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html
Thank you.

Read More...

1 Answer

Hi Carolyn. Remove power to the unit. Remove back assembly. On the left there is a vertical blower wheel housing. There are 2 electrical devices connected to the housing. The thermal fuse is approximately 1/2 " wide and 1-1/4" long with 2 - blue wires attached. If This is open (Test with an ohm meter), it normally reads closed. This opens when too much exhaust heat is backed up into the dryer. Clean your entire vent system, and make sure your vent cap outside works properly or you might be replacing this again. The thermal fuse is part # WP3392519. Thank you.

Read More...

1 Answer

Hi Gary. We will need your correct model # to assist you. You are possibly looking at a door switch. Your model # is inside the front panel as you open the door. Thank -you.

Read More...

1 Answer

Hi! If the motor does not come on when you press the start button then it could be the fuse WP3392519. You will also want to make sure you are getting 240 volts to the unit from the breaker box. If one of the circuits is off, it will get enough power to run the motor but not heat. If the fuse is blown, you will want to make sure the vent tubing is clear of any obstructions or the fuse will blow again. Thanks

Read More...

1 Answer

Hello Judy! If you let the dryer set a while and cool down does it start back up? Thanks.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google