Charles April 25, 2015 for Model Number 1069051055 kenmore side by side refridge Ice maker part # 4317943 What direction do you turn the adjustment dial to increase or decrease the water level fill to change the size of Ice cubes
1 Answer Charles, to increase the water level in this icemaker you turn the adjustment screw clockwise(right) to decrease the water level, you turn the adjustment screw counter clockwise( left). You should first check to make sure you have enough water flow/pressure(32 psi) at the fill valve connection. If you need to adjust the screw more than three revolutions, you need to replace the ice maker. Read More...
Shep April 24, 2015 for Model Number MFI2269VEB6 I mam trying to remove the ice maker from the Maytag unit listed. I have talked with four of your people and sent pictures to David of the ice maker compartment. I have not found any help getting the old maker out. THERE ARE NO SCREWS IN THE SIDE WALL. That unit has the same model numbur but the ice maker compartment on mine does not match the one you have a film of showing how to remove three screws and simple removal. My ice maker is mounted on a plastic tray that appears to slide out after depressing a tab on the rail. CAN'T MOVE IT!! I cannot find what is holding the ice maker to the back wall. I removed the three screws in the bottom of the tray and can move the maker around, up and down a half inch but can't pull it forward at all! CAN YOU HELP? I have the manual and can get picctutres on the computer
2 Answers Shep, Simply removing the 3 screws from the bottom will not allow this icemaker to come out. To remove you will need to pull out the ice bin. On the lower left side of the ice compartment there is a cover that needs to be removed. You will see a hole on the cover just below where the head of the icemaker is. Using a small flat blade screwdriver, stick it into the hole at an angle with the handle up. Then pull the handle downward and it will catch the release for the cover. Slide the cover forward. Once this is done then disconnect the wire harness and then at the side of the icemaker there will be a tab, Pull the tab toward the icemaker and slide the entire assembly forward. This will allow for the icemaker to be removed. Read More...
Shep April 24, 2015 for Model Number MFI2269VEB6 I mam trying to remove the ice maker from the Maytag unit listed. I have talked with four of your people and sent pictures to David of the ice maker compartment. I have not found any help getting the old maker out. THERE ARE NO SCREWS IN THE SIDE WALL. That unit has the same model numbur but the ice maker compartment on mine does not match the one you have a film of showing how to remove three screws and simple removal. My ice maker is mounted on a plastic tray that appears to slide out after depressing a tab on the rail. CAN'T MOVE IT!! I cannot find what is holding the ice maker to the back wall. I removed the three screws in the bottom of the tray and can move the maker around, up and down a half inch but can't pull it forward at all! CAN YOU HELP? I have the manual and can get picctutres on the computer
2 Answers Hello Shep. You must remove the wire cover on the left wall. Then unplug the wires and release the locking tab at the top of the icemaker and slide the whole assembly, not just the icemaker, out of the housing by pulling it toward you. Now you can replace the icemaker. Read More...
Erik April 20, 2015 for Model Number MFI2269VEM10 I have a Maytag french door refrigerator, model MFI2269VEM10. Currently, the ice maker, water dispenser, and interior lights do not work. Last month, I had the same problem and was able to remedy it by sliding out the door/tray to the ice maker and closing it, somewhat forcefully. That didn't work this time. The light just flickered with each attempt. Could it be a bad switch somewhere in the ice maker that shuts everything off? Thanks for your assistance.
1 Answer Hello Erik. You need to go over all wiring connections and look for bad or loose connections on the unit. Read More...
Dean April 19, 2015 Ice builds up in the water shoot and no water can get to the tray, but the icemaker still goes threw the proses of making and empting the tray.
1 Answer Hello Dean. It sounds like the water valve is bad and will need to be replaced in the unit. Read More...
Guardrail72 April 10, 2015 I have a whirlpool French door refrigerator the ice maker is making ice. The ejector blade turns but its acting as if the ice is freezing to the mold. How do I check to see if the mold heater is working?
1 Answer Hello guardrail72. You can test the heater for continuity. It should read closed. If the icemaker cycles, but the heater does not melt to release the ice, then it is bad and you will need to replace the icemaker assembly. Read More...
Marty March 25, 2015 for Model Number KSRS25FGWH02 I went out of town and turned off the ice maker and water to home. Turned all back on on return and all was fine. Then ice maker started only producing 4 cubes per cycle. I flushed incoming water line and some debris came out, but ice maker still does the same. I also removed fill valves but the screen appeared clear. So is the fill valve partially plugged, or is the control module or ice maker bad? I have tried adjusting the ice size screw, but it hasn't made a difference. Thanks
1 Answer Hello Marty, The water valve W10408179 will have to be replaced if proper water pressure is being supplied to the unit from the home water supply. You should also try to get the icemaker fill adjustment back as close to the way it was originally to prevent issues with the water fill. As a note, you cannot turn the adjustment screw more than one turn either direction or damage will be incurred on the contracts inside the motor module. Read More...
Tqammy March 19, 2015 for Model Number ed25dq Our Whirlpool refrigerator icemaker has been having thin black stuff coming off. Then big peice came off, like seal. Now water doesnt fill tray but is freezing as a big block where water inlet is.
1 Answer Tqammy, The ice freezing at the fill cup would be caused possibly by either the water filter needing to be changed and causing the water pressure to be too low and causing it to freeze up or by low water pressure to the unit. The black stuff coming off in the ice would be caused by particles of the icemaker model deteriorating. You will want to check to make sure that the model is not damaged and if it is you would want to replace the icemaker. Read More...
Louie March 18, 2015 Replaced old ice maker, makes ice but the cubes are frozen together. Possibly the tray is over full?
1 Answer Hello Louie. Make sure the temp in the unit is 0 to 5°. If so, you will need to replace the water valve in the unit. Read More...
Charley C. March 11, 2015 for Model Number Whirlpool Our icemaker leaks, but not inside the the freezer. What parts do I need to replace the incoming water lines? Would it be wise just to replace everything, ice maker too?
1 Answer Hello Charley. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...