Range / Cooktop / Oven Panel Parts

This replacement panel broiler restores the oven's internal broiler surface so heat reflects properly for consistent top-heat cooking and protects internal components from direct flame and spills. Fits the oven broil cavity where the broil element mounts. What it does:

• Provides the mounting and protective surface for the broil element and helps reflect broil heat across food
• Restores even browning and searing when a damaged or warped panel causes uneven broiling
• Protects internal oven walls and wiring from grease, drips and direct flame contact
• Helps reduce smoke and flare-ups caused by burned-on residue on a damaged panel

• One replacement inner broiler panel

• Disconnect power to the appliance before servicing to avoid shock hazard
• Basic hand tools are typically required; handle edges carefully — panel may have sharp metal edges
• Clean surrounding area and broil element before installation; replace only with the exact part number shown

This retainer is a small mounting clip that keeps a nearby component held securely in place, helping prevent rattles and misalignment for reliable appliance operation. Install restores proper positioning of the secured part. What it does

• Holds a component or assembly in its intended position to prevent movement or vibration
• Common symptom: loose or rattling parts near the retainer location
• Common symptom: component shifts or comes partially detached during operation
• Works as a replacement for a cracked, broken, or missing retainer that fails to secure the part

• One retainer

• Disconnect power (unplug appliance or switch off circuit breaker) before beginning any repair
• Accessing the retainer may require removing a panel or adjacent parts; keep fasteners organized
• Use basic hand tools; avoid forcing parts to prevent damage to surrounding components

This replacement base restores a solid mounting platform for the assembly it supports, keeping components aligned and secure. Replace a cracked or warped base to eliminate looseness, rattling, or misalignment that can lead to premature wear.

• Supports and secures the associated assembly for proper operation
• Maintains alignment to reduce vibration and noise during use
• Helps protect connected parts by preventing shifting and flexing
• Replace when you see cracks, warping, stripped/broken mounts, or symptoms like rattling, looseness, or poor fit

• Disconnect power; shut off water or gas if applicable
• Wear cut-resistant gloves and handle edges carefully
• Document screw locations/routing; transfer any reusable clips or bushings from the old base
• Start screws by hand and avoid overtightening, especially into plastic bosses

This control panel is the front fascia that houses the cycle buttons and indicators on your appliance. Replacing a damaged or unresponsive panel restores reliable selections and a clean, factory appearance.

• Provides the user interface for selecting cycles and options
• Communicates button presses to the control system to start and customize operation
• Covers and protects components while finishing the appliance's front
• Common symptoms: cracked/broken console, worn or sticky buttons, selections not registering, intermittent response

• Disconnect power at the breaker before servicing
• Remove mounting screws/clips to release the existing console; support it to avoid straining wiring
• Transfer the user interface module and any brackets from the old panel as needed; avoid pinching ribbon cables
• Reinstall hardware and verify button response before completing reassembly

This oven door glass assembly replaces damaged or cracked door glass to restore a clear viewing window and help keep the oven cavity sealed. It's a direct-fit replacement for affected Frigidaire oven doors. What it does:

• Replaces cracked, chipped or broken oven door glass to restore safe, visible operation.
• Lets you monitor cooking without opening the door to prevent heat loss from frequent door openings.
• Helps the door maintain its sealed barrier for more consistent oven performance.
• Matches OEM form for straightforward fit and alignment when installed correctly.

• Disconnect power (and gas if applicable) before starting; handle glass with thick gloves and eye protection.
• Installation may require removing the oven door and several screws—keep parts organized and follow OEM instructions.
• Inspect door seals and mounting hardware while replacing the glass; replace any damaged components.

The Control Panel is an OEM part for Whirlpool ranges. It facilitates precise input and display of cooking functions.

Causes of replacement include failure of embedded circuits or damage allowing moisture penetration through the membrane surface over time. Physical impacts can distort switch responsiveness.

Symptoms of issues involve:

• Ghosting or pixelation impairing display readability
• Refusal of elements to toggle through temperature settings
• Unresponsive selection buttons due to circuit interruptions
• Inaccurate temperature calibration requiring technician attention

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.