Range / Cooktop / Oven Regulator Or Pressure Regulator

This pressure regulator controls incoming water pressure to the appliance's water/ice system, helping maintain steady flow for proper dispenser and ice maker operation. Replaces a worn or failing regulator to restore correct water delivery. What it does:

• Reduces and stabilizes incoming household water pressure for the appliance's water valve/ice maker
• Helps prevent overfilling, leaking, erratic dispenser flow, or poor ice production caused by excessive pressure
• Works with the water inlet system to ensure consistent fill cycles and reliable dispensing
• Compatible with models that use WP74006429 as the factory regulator

• One pressure regulator

• Shut off water supply and unplug the appliance before replacing the regulator
• Inspect fittings and tubing for damage; replace any worn connectors or seals
• Tighten fittings securely and check carefully for leaks after restoring water and power

This valve/regulator assembly controls gas flow to the burner, restoring correct gas pressure and ignition response in compatible gas appliances. Use it to address heating issues and unstable or inconsistent burner operation. What it does:

• Regulates and meters gas pressure delivered to the burner for proper combustion.
• Opens and closes gas flow during the ignition cycle to maintain a steady flame.
• Common symptoms it can address: no heat, weak or uneven flame, or burners that fail to light.
• Designed as a direct replacement assembly—matches OEM function and form for affected gas systems.

• Shut off gas supply and disconnect electrical power before attempting replacement.
• Replace gaskets/seals as needed and tighten gas fittings per manufacturer torque specs; check all connections for leaks with soapy water (do not use an open flame).
• Follow model-specific instructions and diagram for correct routing and mounting.

The Pressure Regulator is an OEM replacement part for Bosch gas cooktops. It maintains consistent burner flame levels for precise meal preparation, maximizing fuel efficiency. Even pressure safeguards safety through controlled gas flow.

Causes of a bad pressure regulator can include deteriorating diaphragm seals or valve shafts due to repetitive operations over the appliance's lifespan. Mineral scales from sediment in gas lines threaten integrity.

Symptoms of a bad pressure regulator include:

• Flames lift or flare away from burner heads unpredictably   
• Burners cannot maintain set heat levels, constantly cycling 
• Difficulty achieving desired flame height or cooktop shuts off
• Potential safety hazards like uncontrolled gas leakage

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This valve control assembly regulates gas flow to a range or oven burner, replacing a failed valve to restore proper ignition and heat control. Designed as a direct-replacement service part to help return safe, reliable operation. What it does:

• Controls gas flow to burners or the oven burner so you can set and maintain heat levels
• Replaces a valve that is stuck, not opening, or not responding to temperature/knob input
• Commonly used when burners or oven won't light or when heat output is inconsistent
• Works with existing manifold and burner hardware when the valve assembly is the faulty component

• Turn off electrical power and shut off the gas supply before beginning work
• Only install the exact replacement PN for this appliance;
• Use approved fittings and test all gas connections for leaks (soap solution) after installation
• If you detect a gas odor or are unsure about any step, stop.

This regulator controls gas pressure to the range/oven so burners and the oven heat consistently and safely. Replaces a failed regulator to restore proper flame behavior and reliable cooking performance. What it does:

• Regulates incoming gas pressure to the appliance's burner system
• Helps maintain steady, even flame height for consistent cooking
• Resolves symptoms like weak or uneven flames, burners that won't light, or poor oven heat
• Prevents over-pressurization that can cause unstable burner operation

• One regulator

• Turn off the gas supply and electrical power before beginning work
• Install using proper fittings and thread sealant rated for gas; tighten to OEM torque specs
• After installation, test all gas connections for leaks (do not use an open flame)

The Pressure Regulator is an OEM part for Frigidaire gas ranges. It controls incoming gas flow to the burner valves and maintains consistent heat levels.

Causes of a bad pressure regulator can include cracks or leaks developing in the seal over time, clogs or debris buildup affecting flow control, or damage to pressure monitoring components.

Symptoms of a bad pressure regulator include:

• Fluctuating burner flames and heat output
• Inability to stabilize gas pressure for predictable cooking
• Yellow or sooty flames indicating inefficient combustion
• Safety risk of gas leaks at increased pressures

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This pressure regulator controls and stabilizes incoming water pressure to the appliance, helping maintain consistent operation and protect internal valves and seals. Fits systems that use a 3/4 inch inlet regulator. What it does:

• Reduces high incoming water pressure to a safe, steady level for the appliance
• Prevents pressure-related leaks, valve chatter, and premature wear on seals
• Helps maintain consistent water flow for reliable cycles and operation
• Commonly replaced when irregular pressure, humming valves, or water leaks occur

• One pressure regulator (3/4 in.)

• Turn off water supply and power to the appliance before starting; relieve system pressure first
• Inspect connection fittings and seals; use appropriate thread sealant if required by the OEM
• Tighten to manufacturer torque recommendations and check for leaks after restoring water

This gas pressure regulator controls fuel flow to the appliance's burner system, keeping flame size and heat steady for reliable cooking. Replaces a worn or failed regulator to restore proper gas delivery and consistent burner operation. What it does:

• Regulates incoming gas pressure to the appliance's burners and oven for consistent flame and heat.
• Helps correct symptoms such as weak or uneven flames, burners that won't light properly, or poor oven heating.
• Prevents over-pressurization that can cause unstable combustion when functioning correctly.
• Works as the inline control between the gas supply and the appliance's valve system.

• Turn off the gas supply and electricity to the appliance before attempting service.
• Use proper gas fittings and thread sealant rated for gas; follow local codes.
• After installation, perform a leak test on all gas connections and verify burner flames are steady.

This pressure regulator controls gas flow to the range valve, helping maintain steady burner operation for safe, consistent flames. It replaces a worn or failed regulator to restore proper gas delivery and reliable ignition performance. What it does:

• Regulates incoming gas pressure to the range's control valve for steady burner flames
• Helps correct issues like weak or uneven flames and burners that struggle to light
• Reduces risk of high-pressure surges that can affect burner performance
• Works as a direct replacement when the existing regulator is faulty or leaking

• Turn off the gas supply and power before starting any work; always follow appliance shutoff procedures
• Inspect fittings and seals; use proper thread sealant for gas-rated connections if required by the manufacturer
• After installation, perform a gas leak check and verify correct burner operation and flame appearance

This pressure regulator controls and stabilizes the gas flow to the appliance, helping the burner maintain a steady, correct flame for reliable heating and cooking performance. What it does

• Regulates gas pressure to the appliance's burner assembly for consistent ignition and flame size
• Can correct low or uneven burner flames when the regulator is failing
• Helps prevent frequent burner shutdowns and poor temperature control linked to pressure issues
• Works as part of the appliance's fuel delivery system to ensure safe, steady operation

• One pressure regulator

• Turn off the gas supply and disconnect power before attempting service
• Use proper gas fittings and thread sealant rated for gas lines; check for leaks after installation

This gas pressure regulator controls the flow of natural gas or LP to the cooktop and oven valves, helping restore correct burner and oven flame performance for safe, even heating. What it does

• Regulates incoming gas pressure to the appliance's valve system so burners and oven receive consistent fuel flow
• Can correct symptoms such as burners that burn too high or too low, uneven heating, or oven temperature inconsistencies
• Works as part of the appliance's gas delivery system to maintain steady flame behavior
• Designed as a direct replacement to restore original gas flow control

• One regulator

• Turn off gas supply and electrical power before beginning service
• Inspect gas fittings and connections; use approved fittings and test for leaks after installation
• Do not modify the part; replace with the exact regulator specified for the appliance

The Regulator is an OEM part for GE gas ranges and ovens. As a key safety component, the regulator is responsible for maintaining a consistent gas pressure and flow to the burners. It works to reduce higher pressure gas from the supply line to a lower, more controlled pressure required for safe and efficient burner operation.

Causes of a bad regulator can include corrosion or degradation of internal components over many years of use. The precisely calibrated mechanisms that control gas flow can malfunction if wear and tear afflict the regulator.

Symptoms of a bad regulator include:

• Inconsistent or unpredictable burner flame
• Flames that fluctuate between high and low
• Burners that fail to light or stay lit
• Difficulty achieving or maintaining proper cooking temperatures

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This gas pressure regulator controls and stabilizes incoming supply pressure to the appliance manifold, helping ensure consistent burner flames and reliable ignition. Replace if the original regulator is sticking or no longer maintaining correct pressure.

• Regulates incoming gas to the appliance's rated manifold pressure
• Helps maintain even flame height and proper combustion
• Supports reliable burner ignition and reduces flame-out from pressure swings
• Common symptoms include weak or uneven flames, yellow tipping, burners not lighting or not staying lit, or flames that are too high

• Disconnect electrical power and shut off the gas supply before servicing
• Observe the flow-direction arrow; install with outlet toward the appliance manifold
• Use approved gas-rated thread sealant on male threads only and leak-test all joints with a non-corrosive solution after installation