Range / Cooktop / Oven Tube Or Fitting

This replacement water tube delivers water from the household supply to the ice maker, restoring reliable filling and ice production. It replaces worn or cracked tubing that can cause leaks or prevent the ice maker from filling. What it does:

• Carries water to the ice maker fill valve so the ice maker can fill and form ice
• Stops and helps prevent leaks caused by cracked or brittle tubing
• Restores normal ice production when a damaged tube is keeping the ice maker from filling
• Helps ensure consistent dispenser or fill-line water flow when properly connected

• Turn off the refrigerator power and shut off the water supply before starting.
• Disconnect the ice maker and remove access panels as needed to reach the tube.
• Inspect fittings and replace any damaged clamps or seals; tighten connections to manufacturer torque where specified.
• After installation, restore water and power, then check carefully for leaks and confirm the ice maker fills normally.

This gas tubing replacement routes fuel between the appliance gas manifold and control valve to restore safe, reliable fuel delivery. Use it when tubing is damaged, corroded, or leaking to help eliminate gas leaks and restore normal burner operation. What it does:

• Channels natural gas or LP from the manifold to the valve and burners for ignition
• Replaces cracked, corroded, or kinked tubing that can cause leaks
• Addresses symptoms like a gas smell near the appliance, burners that won't light, or intermittent flame
• Keeps fuel flow consistent so burners heat predictably when controls are on

• Shut off the appliance gas supply and disconnect power before starting work
• Tighten fittings to manufacturer torque; check all connections for leaks with a soap solution or approved gas leak detector
• If you smell gas during or after installation, stop and ventilate the area.

Gas tubing for ranges and cooktops. Connects gas supply to burners. Replace if cracked, kinked, worn, or damaged to restore safe gas flow.

Gas tubing component for cooktop burner assemblies. Replaces cracked, damaged, or worn gas supply tubes. Essential structural part for safe gas flow.

This threaded connector secures or joins short sections of tubing or hose on select appliances, restoring a tight, reliable connection. Use when the original nipple is corroded, stripped, or leaking. What it does:

• Provides a secure, threaded connection between tubing, hose, or fittings
• Maintains a sealed joint to help prevent leaks at the connection point
• Replaces damaged or worn nipples that can cause loose fittings or loss of flow
• Commonly used where a short, durable threaded coupling is required

• One nipple

• Disconnect power and shut off water or gas supply before servicing
• Inspect mating threads and replace any damaged seals or washers
• Hand-start threads to avoid cross-threading, then tighten with the appropriate wrench
• After installation, restore supply and check carefully for leaks during a test run

1/4" gas supply tubing connects your range's gas line to the valve. Replace when damaged, cracked, leaking, or during valve service for safe operation.

Replacement gas tubing for ranges. Installs between gas components to restore secure fuel routing. Needed when original tubing is cracked, corroded, or leaking.

This replacement fitting connects the appliance's water line to its internal plumbing so water flows where it's needed and stays sealed. It restores a proper watertight connection to help stop leaks and ensure reliable water delivery. What it does:

• Connects the external water supply line to the appliance's internal water inlet
• Creates a secure, watertight seal to prevent drips and leaks at the connection point
• Supports consistent water flow for ice makers, dispensers, or valves where used
• Can resolve symptoms like visible leaks, reduced water flow, or intermittent filling

• One replacement fitting

• Turn off the water supply and unplug the appliance before installing
• Inspect mating surfaces and replace any damaged O-rings or gaskets as needed
• Hand-tighten first, then snug with appropriate tools; avoid over-tightening
• If plumbing sealant is recommended by your installer, use plumber's tape on threaded connections only

This tubing assembly routes water inside the refrigerator to the dispenser/ice system, restoring a sealed water path and reliable flow. Use it to replace cracked, kinked, or leaking tubing for better water delivery. What it does:

• Carries water from the inlet to the dispenser/ice components to enable ice and water dispensing
• Stops leaks and seepage caused by cracked or damaged tubing
• Restores proper water routing when bends or kinks restrict flow

• Tubing assembly

• Turn off the refrigerator and shut off the water supply before starting work
• Drain any remaining water from lines and have a towel/container ready for spills
• Inspect connections and use new fittings or seals if the old ones are damaged

Supplies gas from manifold to burner assembly. Replace if cracked, corroded, kinked, or leaking to restore safe fuel delivery to your gas range burners.

Pilot gas tube elbow fitting for gas cooktops. Connects gas line to pilot assembly with 3/16" angled connection. Replace if cracked, damaged, or leaking.