Range Hood Housing Or Cover

Keep your appliance's controls working reliably with this switch cover. It mounts over a switch to hold it in place and shield it from damage, helping ensure consistent actuation and long service life.

• Retains and protects a control/interlock switch within its housing
• Helps keep the switch aligned for reliable on/off detection
• Shields the switch from dust and incidental contact
• Cracked, loose, or missing cover can cause intermittent operation or no response when the control is pressed

• Disconnect power to the appliance before servicing
• Remove the necessary panel to access the switch; note wire positions/orientation
• Transfer any clips/screws from the old cover and seat the switch fully
• Secure wiring away from pinch points before reassembly

This switch cover is a small protective cap that mounts over a control switch in the appliance's console. It helps keep the switch aligned and shielded so the button operates smoothly and the control remains reliable. What it does:

• Retains and protects a control switch within the console/control panel
• Helps ensure consistent button feel and proper actuation
• Helps keep dust and debris away from the switch area
• Replace if cracked, missing, or deformed; symptoms can include a loose or stuck button, intermittent on/off response, or failure to start

• 1 switch cover

• Disconnect power to the appliance before servicing
• Access the control panel to reach the switch area
• Note the cover's orientation; seat it fully and ensure a secure fit
• Reassemble the panel and test switch operation before restoring power

This replacement cover fits over the appliance's light housing. It shields the bulb and wiring from grease and moisture while helping keep the lamp assembly secure, restoring safe, consistent illumination. What it does:

• Covers and protects the light housing and bulb from heat, grease, and moisture
• Helps secure the lamp support/assembly in place
• Maintains proper light output and appearance
• Common symptoms include a cracked or missing cover, exposed bulb, loose light assembly, or discoloration around the light opening

• 1 lamp support cover

• Disconnect power to the appliance before servicing and allow the area to cool
• Remove the old cover and retain any original fasteners or clips
• Align and seat the new cover fully; avoid overtightening fasteners
• Restore power and test the light for proper operation

This switch box is the outer housing that protects and organizes oven/stove control switches and wiring, helping keep electrical components secure and stable for reliable cooktop operation. What it does:

• Holds and shields control switches and related wiring from spills, heat, and movement
• Provides secure mounting points for switch terminals to prevent loose connections
• Helps prevent shorting, arcing, and exposure of live wiring
• Restores proper alignment of controls when cracked, melted, or broken

• Disconnect power at the breaker before starting any repair to avoid shock or injury
• Inspect and label wiring before removal; reattach wires to the same terminals
• Handle sharp edges and retainers carefully; some models use clips or screws for attachment
• If switches or wiring are damaged, replace those parts as well for a complete, safe repair

This scroll is the blower housing that directs airflow inside the ventilation blower assembly, restoring proper exhaust flow and helping reduce noise from an unstable blower. It fits into the blower motor assembly to channel air through the fan. What it does:

• Channels and directs airflow from the blower wheel to the exhaust duct
• Helps position and support the blower wheel for stable operation
• Worn or damaged scrolls can cause reduced airflow or poor exhaust performance
• Cracks, deformation, or loose fit may create vibration or unusual noise

• Disconnect power to the appliance before any service to prevent electrical hazard
• Installation typically requires removing the blower assembly and a few fasteners; keep track of screws and orientation
• Inspect the blower wheel and motor during reassembly; replace any damaged components
• Handle edges carefully and test operation after installation to confirm airflow and quiet operation

Replacement top panel for the unit's housing. It restores a secure cover over internal components and proper airflow containment when the original top is bent, cracked, or missing, helping the ventilation system operate as intended.

• Forms the upper cover of the housing and shields internal parts
• Helps direct and contain airflow through the unit
• Provides mounting or clearance for components and wiring pass-throughs as designed
• Typical failure signs: dents or cracks, air leaks, vibration/rattling, reduced airflow, or trouble aligning fasteners

• Disconnect power at the breaker before servicing.
• Support the hood/assembly and remove filters or covers as needed to access fasteners.
• Keep track of hardware; transfer any gaskets, clips, or components from the original top.
• Edges can be sharp—wear cut-resistant gloves; align and tighten fasteners evenly to avoid gaps.

A protective terminal boot that slips over a capacitor connection to shield it from moisture, dirt and accidental contact, helping reduce risk of shorts and maintain a reliable electrical connection. What it does:

• Covers the capacitor terminal to reduce the chance of accidental contact and arcing.
• Protects the terminal from moisture, dust and debris that can compromise electrical connections.
• Helps prevent corrosion and keeps the terminal area cleaner for more reliable operation.
• Signs it may be needed: cracked, torn or missing boot; visible arcing or burn marks near the capacitor; intermittent electrical behavior that points to a compromised connection.

• Always disconnect power and unplug the appliance before working on electrical components.
• Discharge the capacitor per OEM instructions before touching terminals to avoid shock.
• Push the boot fully onto the terminal for a snug fit; ensure no wiring is pinched or under strain.

This cover plate is a factory-style trim panel that protects and finishes the appliance's control area and internal components, restoring a clean appearance and helping keep wiring and switches shielded from debris. What it does

• Covers and protects the appliance control area and underlying components
• Restores a finished look to a damaged or missing trim panel
• Helps prevent dust and spills from reaching electrical parts or switches
• Matches OEM fit and mounting points for a secure replacement

• One cover plate (trim panel)

• High-level replacement; typically removed and installed with basic hand tools
• Disconnect power to the appliance before starting to avoid shock or injury
• Inspect mounting clips and fasteners and replace if worn for a secure fit

This membrane switch touch pad replaces the worn or unresponsive touch controls on your appliance's control panel to restore normal button responsiveness and user input for oven/range functions. What it does

• Acts as the touch-responsive interface for the appliance control panel.
• Replaces cracked, faded, or unresponsive touch buttons that fail to register commands.
• Helps resolve intermittent or non-working control-pad functions and missed presses.
• Restores tactile/visual button feedback when paired with a functioning display/control board.

• One membrane switch touch pad.

• Disconnect power to the appliance (unplug or switch off circuit breaker) before beginning work.
• Remove control panel trim carefully to access and replace the membrane; avoid bending or creasing the new switch.
• Reconnect ribbon/plug firmly and confirm correct alignment before reassembly.