Refrigerator Drawer, Shelf, Pan

Replace your cracked or worn snack drawer track pan to restore smooth sliding and keep food organized in your side-by-side refrigerator compartment.

This crisper drawer stores fruits and vegetables in your refrigerator's humidity-controlled compartment. Replace if cracked, broken, or missing.

This connector joins two sections of the refrigerator's water tubing to create a secure, leak-resistant seal. Replace a cracked or loose connector to restore proper water flow to the dispenser and ice maker.

• Provides a sealed union between two water tubes in the appliance's water system
• Helps prevent air and water leaks that can impact dispenser and ice maker performance
• Typical failure signs include drips or puddles near the connection, visible seepage, or moisture alerts
• Also causes low/no dispenser flow or small or hollow ice cubes

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Prepare tubing with a clean, square cut; insert each tube fully into the connector until seated, then pull-test to retention
• Restore water and check all joints for leaks; purge air by dispensing water before normal use

Structural support that holds and aligns shelves or racks in your side-by-side refrigerator. Replace when worn, broken, or missing to restore stability.

The Drawer Glide Gear is an OEM replacement part for Frigidaire refrigerators. It is a metal component located on each side of wire shelf tracks that work together to make shelf and drawer movements smooth. 

Causes of bad glide gears can include wear from years of extended usage, dents or deformation that restrict proper motion, or failure of lubricating parts inside the gear mechanism.

Symptoms of a bad Drawer Glide Gear include:

• Shelves or drawers that stick or fail to slide freely
• Noisy squeaking or grinding noises coming from shelf areas  
• Shelves difficult to properly align or position as needed

As a high-stress moving part, glide gears can degrade and lead to slothful storage access over time. Replace with this genuine OEM component for optimally smooth shelf performance on your Frigidaire refrigerator. The replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement door bin for refrigerator inner door storage. Installs on door panel to hold bottles, condiments, and small items. Replace if cracked, broken, or missing.

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Shallow deli drawer for storing meats and cheeses in your refrigerator. Replace when cracked, broken, warped, or missing to restore organized storage.

Removable silverware basket for the dishwasher lower rack that keeps forks, knives and spoons separated and upright during wash cycles, helping prevent items from shifting, nesting, or blocking spray for better cleaning results. What it does:

• Holds cutlery and small utensils securely to improve wash coverage and reduce nesting.
• Keeps sharp items contained to help protect dishes and reduce movement during cycles.
• Replaces cracked, broken, or missing baskets that allow silverware to fall through the rack.
• Easy to clean—simply rinse or place in the dishwasher top rack if needed.

• Typically installs without tools: slide out the lower rack and set the basket into the designated rack area.
• Ensure the basket is oriented correctly and does not obstruct rack travel or spray arms before running a cycle.
• Inspect surrounding rack tines and clips for damage while replacing the basket.
• Refer to the appliance owner's manual or service guide for model-specific instructions and safety information.

The  Door Bin Assembly is an OEM part for Frigidaire refrigerators. This door bin provides convenient and accessible storage for a variety of items, from condiments and jars to drinks and snacks. By attaching to the inside of the refrigerator door, it maximizes space efficiency, allowing for better organization and management of refrigerator contents.  

Causes of a bad Door Bin Assembly can include physical damage, such as cracking or breaking from overloading or impact, wear that leads to a loose fit or difficulty in securing the bin to the door, and degradation over time that affects its structural integrity.

Symptoms of a bad Door Bin Assembly include:

• The bin detaching from the door or not holding securely, risking spills or falls.
• Visible cracks or damage that compromise the bin's capacity or safety.
• Difficulty fitting into its designated slot, indicating potential warping or damage to the attachment points.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This duct assembly routes internal airflow in the appliance, replacing damaged or worn vent tubing to restore proper air movement. It helps reduce air leaks and airflow-related performance issues when the original duct is compromised. What it does:

• Channels blower air from the fan housing to the exhaust path to maintain proper ventilation.
• Replaces collapsed, torn or disconnected ducting that can cause poor airflow.
• Addresses symptoms such as reduced drying/cooling performance, longer cycles, or warm cabinet air.
• Helps eliminate drafty or noisy airflow caused by gaps or damaged duct sections.

• Disconnect power (and turn off gas supply for gas appliances) before beginning service.
• Access may require removing rear or lower access panels; keep hardware organized for reassembly.
• Inspect and replace any damaged clamps, seals or gaskets during installation for a proper seal.

Replace a cracked, broken, or missing refrigerator shelf. Restores a stable storage surface inside your fridge for organizing food and beverages securely.

Holds bottles, jars, and condiments on your refrigerator door. Replace this bin if it's cracked, broken, or missing to restore organized storage space.

Sliding utility pan drawer for refrigerator storage compartments. Replace if cracked, broken, or roller glides are worn causing rough sliding action.

This rear glass shelf trim replaces the finished glass edge at the back of a refrigerator shelf, restoring a secure seat and clean appearance. It helps keep items from sliding off and reduces gaps where spills can drip. What it does:

• Provides the finished rear edge and support for a refrigerator glass shelf.
• Helps the shelf seat and lock into position; a broken or missing trim can prevent proper seating.
• Reduces food/items from shifting toward the cabinet rear and helps contain minor spills.
• Restores appearance when the original trim is cracked, chipped, or worn.

• Handle the glass trim carefully; wear cut-resistant gloves and eye protection during installation.
• Remove the shelf per the appliance's OEM instructions before replacing the trim, then refit the shelf and verify it seats properly.
• Inspect mounting clips or supports and replace if damaged to ensure a secure fit.

Replacement shelf divider that installs on refrigerator shelves or bins to organize items and prevent shifting. Replaces cracked, broken, or missing dividers.