Parts for Kitchenaid KSSP48QMS03: 04 - Refrigerator Liner Parts

Replace your refrigerator water filter every 6 months for clean, fresh-tasting water and ice. Simple twist installation. Verify fit with your model number.

Refrigerator not cooling properly or freezing food? This temperature sensor thermistor monitors internal temps and signals the control board. DIY fix.

Replace your refrigerator's air duct if cracked, broken, or missing. This duct routes cold air between compartments to maintain proper temperature.

This thermistor clip secures the refrigerator/freezer temperature sensor in the correct position for accurate temperature readings and consistent cooling. It helps keep the sensor stable so the control can properly monitor and adjust appliance temperature. What it does:

• Holds the thermistor/sensor in place on evaporator or cabinet surfaces to ensure reliable contact
• Helps prevent sensor movement that can cause incorrect temperature readings or erratic cooling cycles
• Supports proper airflow around the sensor for accurate thermostat feedback
• Simple, passive mounting solution that maintains sensor location after service

• Includes: 1 thermistor clip

• Designed for a direct replacement; remove power to the appliance before servicing
• Handle the sensor and wiring gently to avoid damage to the probe or connector
• Confirm sensor location per manufacturer guidance before clipping to ensure correct placement

This screw support secures the dryer drum ladder assembly, helping maintain proper alignment and stable rotation for reliable drying performance. It replaces a worn or broken support to reduce noise and rattling during operation. What it does:

• Holds the ladder/support bracket in place so the drum rotates smoothly.
• Prevents excessive movement that can cause scraping, knocking, or rubbing noises.
• Restores correct positioning to reduce wear on adjacent components.
• Suitable when the original support is cracked, bent, or missing fastener points.

• One screw support (ladder) as shown.

• Intended for experienced DIYers; confirm compatibility with your model before installing.
• Disconnect power (unplug electric or shut off gas and unplug) before beginning work.
• Handle small parts carefully and keep track of fasteners; use appropriate hand tools.

This replacement screw secures appliance panels and components to restore proper fit and stop loose or rattling parts. A simple, OEM-compatible fastener that helps maintain safe, stable operation and original assembly alignment. What it does:

• Secures panels, trim, brackets or components to prevent movement and vibration
• Restores proper fit when a screw is missing or stripped
• Helps eliminate rattling, gaps, or misaligned parts
• Fits the OEM threaded holes and fastening points

• Disconnect power (and gas if applicable) before accessing internal components
• Use the correct driver to avoid stripping the head; hand-start threads before final tightening
• Do not overtighten—stop when snug to avoid damaging threads or plastic parts
• Keep removed hardware organized to ensure correct reassembly

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

If your refrigerator isn't staying at the right temperature or runs too warm, the thermistor may have failed. This sensor monitors compartment temps.

Meat pan baffle lid for side-by-side refrigerators. Covers the meat drawer baffle assembly. Replace if cracked, broken, or missing.

Fixes uneven cooling or ice buildup in fridge compartment. This air baffle assembly directs airflow between freezer and fresh food sections. Moderate DIY.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Fixes warm refrigerator with cold freezer by restoring airflow between compartments. Regulates air distribution for even cooling. DIY-friendly repair.

Fix food freezing on lower shelves with this air diffuser assembly. Restores even airflow and consistent temperatures throughout your refrigerator.

Fix inaccurate cooling or freezing issues with this refrigerator temperature sensor. Sends temperature data to the control board for proper regulation.

Fix incorrect temperature readings or freezing in your fridge. This temperature sensor helps regulate cooling. Easy 15-minute DIY repair with one screw.

This refrigerator door spacer maintains proper alignment and spacing between door components. Replace if cracked, worn, or missing to restore fit.

Door shelf retainer bar for side-by-side refrigerators. Secures items on door shelves. Replace if cracked, broken, or missing to prevent items from falling.

Replace your refrigerator door seal gasket to restore airtight closure and improve energy efficiency. Prevents warm air leaks and frost buildup. Verify fit with your model number before ordering.