Parts for Ge GSE26HMECHES: Refrigerator Section Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Size: 10-32 GXTT FLP.595 S

Sheet metal screw secures refrigerator panels, trim, and brackets. Replace missing, stripped, or corroded screws to restore proper fit and assembly.

Replace your refrigerator's water filter cover cap if it's cracked, broken, or missing. This protective cap installs over the water filter housing.

White plastic clip that secures the rear of refrigerator shelves or drawer rails to the cabinet wall. Replace if cracked, broken, or missing.

Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.

Air return grille installs at the bottom of the fresh food compartment behind the drawers. Replace if cracked, broken, or missing after cleaning.

Plastic cover that protects the damper assembly inlet/discharge area in your refrigerator. Replace if cracked, broken, or tabs are damaged.

Secures refrigerator panels, brackets, and trim. Replace if screw is stripped, missing, or no longer holds components tightly in place.

Rubber grommet secures the base grille on your refrigerator. Replace if cracked, worn, or missing to restore a snug fit and reduce vibration or rattle.

Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.

The Temperature Sensor Seal is an OEM part for GE refrigerators. This seal is designed to protect the temperature sensor from moisture and other environmental factors that could affect its accuracy and longevity. By providing a barrier against the harsh conditions within a refrigerator, such as humidity and temperature fluctuations, this seal ensures that the sensor can accurately monitor and control the refrigerator's internal temperature.

Causes of a malfunctioning Temperature Sensor Seal can include wear and tear over time, degrading the seal's effectiveness. Physical damage like tears or punctures can allow moisture to reach the sensor. Improper installation may leave gaps or loose areas around the sensor, compromising the seal.

Symptoms of a bad Temperature Sensor Seal include:

• Inaccurate temperature readings.
• Condensation or frost near the sensor location.
• Frequent cycling or unusual patterns in the refrigerator's cooling process.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Protects and covers the interior lamp in your refrigerator's fresh-food compartment. Replace if cracked, broken, or missing to prevent bulb contact.

Protective lens that covers your refrigerator's interior lamp, diffusing light and shielding the bulb. Replace if cracked, yellowed, or missing to restore clean illumination. Confirm fit with your model number.

Replace your worn or broken refrigerator bottom hinge pin. Supports the door and serves as the lower pivot point on the bottom hinge assembly.

Directs airflow from evaporator through the fresh food compartment. Replace if cracked, broken, or missing to restore proper air distribution.

Interior light not working? Replace a faulty refrigerator light socket to restore lighting. Simple hand repair with basic tools in under 15 minutes.

Directs and focuses interior refrigerator light for even distribution. Replace if cracked, missing, or misaligned to restore proper lighting and appearance.

This light socket connects the interior lamp to the refrigerator wiring so the interior light turns on when the door opens. It replaces a damaged or burned socket to restore reliable lighting. What it does:

• Holds the interior lamp securely and provides the electrical contact for operation
• Restores lighting when a damaged socket causes the light to fail or flicker
• Prevents intermittent connections from poor contacts or heat damage
• Works with the appliance's existing wiring and bulb style

• Disconnect power to the appliance before inspecting or replacing the socket.
• Handle bulbs and sockets carefully; use gloves to avoid cuts and for hygiene.
• Test operation after installation; replace the bulb if necessary.

The Light Bulb (40W) is an OEM component for GE refrigerators. As an essential task lamp, it illuminates the interior of the refrigerator and freezer compartments. 

All light bulbs will eventually burn out with consistent use over many years. Vibration during compressor cycles can also potentially disrupt bulb filaments faster. 

Symptoms of a burnt out refrigerator light bulb include:

• Dim or no light illuminating inside refrigerator shelves  
• Shadows and dark spots making it difficult to find items
• Higher utility costs from leaving the door open to see inside

This bulb is also compatible with refrigerators from brands like Hotpoint, RCA, and some Kenmore models. 

Replace your refrigerator's light bulb housing assembly when the interior light fails or housing is cracked. Verify fit using your model number.

Maintains refrigerator door alignment and seal integrity. Replace if door sags, won't close properly, or seal is compromised. Verify fit with model number.

Bottom hinge that supports the refrigerator door weight and serves as the pivot point. Replace if worn, cracked, or causing door misalignment and sagging.

Wire harness assembly for refrigerator freezer compartment lighting. Replace if wires are frayed, connections are loose, or harness is damaged or missing.

Mounting screw for dryers, refrigerators, and side-by-side units. Replaces lost, stripped, or damaged screws during appliance repairs or maintenance.

Replace your refrigerator's light lens cover to restore proper illumination. Install when cracked, yellowed, or missing. Verify fit with your model number.

Covers the air duct opening in the fresh food compartment. Replace if cracked, broken, or missing to shield the inlet and guide airflow properly.

Replacement mounting screw for refrigerator brackets, panels, and handles. Restores secure fit when original fastener is missing, stripped, or damaged.

Fix interior lights that won't turn on, stay on constantly, or delay when opening the door. This switch replacement takes 10-15 minutes with basic tools.

Air separator divider for side-by-side refrigerators. Replaces cracked, broken, or missing air flow dividers in the fresh food compartment.

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Bypass cap allows refrigerator water and ice dispensers to work without a filter installed. Replace if cracked or leaking. Confirm fit with your model.

Replaces the water filter housing manifold that delivers filtered water to your dispenser. Replace if water flow is weak, noisy, or leaking. Confirm fit.

Stores and chills water inside your refrigerator before dispensing. Replace if cracked, leaking, or damaged to restore proper water storage function.

Foam sleeve that insulates refrigerator tubing to reduce condensation. Replace when worn, cracked, or missing to restore padding and protection.

Plastic tube that connects the water tank to the dispenser and ice maker. Replace if cracked, leaking, or damaged to restore proper water flow in your fridge.

Foam insulation wraps around your refrigerator's water reservoir. Replace if torn, crushed, missing, or compressed to prevent tank sweating and condensation.

The Fresh Food Lever Assembly is an OEM part for GE refrigerators. It plays a crucial role in the operation of the refrigerator, enabling the smooth adjustment of settings within the fresh food compartment. This lever assembly is responsible for the user's ability to fine-tune the temperature and humidity levels, ensuring that the food stored inside remains fresh and well-preserved. For the same part in white, purchase WR11X10007.

Over time, the lever assembly may become worn or damaged due to regular use, accidental impacts, or environmental factors such as extreme temperatures or humidity.

Symptoms of a bad Fresh Food Lever Assembly include:

• Difficulty in adjusting the temperature or humidity settings.
• The lever becoming loose or unresponsive.
• Inconsistent temperature control within the fresh food compartment.
• Increased energy consumption as the refrigerator works harder to maintain settings.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.

Molded duct assembly directs cold air from freezer to fresh-food section. Replace if cracked, broken, or damaged to restore proper airflow balance.