Remington Log Splitter Parts

This genuine MTD carburetor assembly provides all of the components to replace a carburetor, including the fastening elements. The purpose of a carburetor is to combine the fuel and air intake into a particular ratio that is ignited by the spark plugs to run the engine. This carburetor assembly contains the carburetor itself and the primer bu. The carburetor assembly might have to be ordered as a complete replacement if there is damage to the carburetor that also affects the fastening parts that attach the carburetor to the engine. If the damage cannot be attributed to a smaller part, the full carburetor assembly should be ordered as a replacement for the damaged carburetor and its attachments. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This carburetor assembly is compatible with log splitters and chipper shredders made by the following brands: MTD and Cub Cadet. This part is sold individually.

A starter handle is a piece that works in combination with several other components to start the engine in numerous machines, including lawn equipment. It works when the user pulls the starter handle grip, attached by a mechanism to the crankshaft. It turns to start the engine. If the starter handle breaks, it will have to be replaced in order to start the machine. Starter handles can become damaged from normal use, misuse, or after an accident.Replacing the starter handle is a simple project. After locating the mechanism it attaches to, typically a sturdy rope or cord, the starter handle should be tied securely to the end of the string. Wear gloves to protect the hands during the process. Test the strength of the attachment before trying to start the machine.This starter handle is a genuine OEM replacement part. It is sold as an individual piece. This starter handle is made of durable, high-quality material. It can be used in devices from MTD, Husky, Troy-Bilt, Yard Machines, and Yard-Man. It is compatible with various lawnmowers, log splitters, trimmers, and other devices with pull start engines.

This muffler stud is an OEM part directly sourced from the manufacturer. The muffler stud connects the muffler to the body of the machine. Over time, stress and tension can cause these muffler studs to become loose or even fall out and become lost. Rust and corrosion due to rain and snow can also cause the muffler studs to become loose. When this happens, the studs should be replaced immediately to prevent the muffler from becoming loose or possibly coming off. If the studs are loose and the connection to the machine's engine is not secure, the machine's noise may become louder, or it could emit smoke.If the studs are loose or broken, make sure the engine has cooled down before installing new studs. Use a wrench to tighten loose muffler studs. If the studs are missing, install new ones and tighten them with the wrench. While installing the new studs, it is good to inspect the muffler for holes or damage that may reduce the performance. These muffler studs are made of high-quality steel and are sold individually. These are made to be compatible with tillers and other small engines manufactured by Cub Cadet, MTD, and Yard Machines.

This is a genuine OEM clamp sourced directly from the manufacturer. It is used in various lawn and garden machines to connect hoses to fittings. It is used to connect piping to water pumps, exhaust pipes to exhaust manifolds, and other similar applications. This connection prevents fluids or air from leaking from the hose. Clamps may be spring or screw/band clamps. Spring clamps require no tools to install and remove; however, the size must be more accurate than when using screw/band clamps. Screw/band clamps are adjustable and can be tightened or loosened. Screw clamps should be inspected periodically to ensure tightness and that the clamps have not rusted.Hose clamps are installed approximately 1/4 inch below the end of the hose. If two clamps are used, there should be 1/4 inch between the two bands. When using a screw clamp, loosen the screw with a screwdriver just enough to fit the clamp over the hose. If using a spring clamp, squeeze the clamp and hold it open. Slide the clamp over the hose and then attach the hose and clamp to the fitting. Slide the clamp into place at the joint and tighten. Do not overtighten. This brass-colored clamp is a spring clamp made of metal; it is sold as an individual unit. This clamp is compatible with many different types of pipes made by various manufacturers.

This exhaust piping is a genuine OEM replacement part sourced directly from the manufacturer; it is used on tiller engines and other small engines. The exhaust piping is part of the muffler system. It connects to the exhaust manifold. As gas is combusted to run the engine, it is forced out through the exhaust manifold and the exhaust piping. This process heats the pipes for a short period. Over a period of time, this repeated heating can cause the exhaust piping to deteriorate. If this happens, the piping will need to be replaced in order for the exhaust manifold to function correctly. If the engine is experiencing overheating problems, the exhaust pipes will need to be replaced when it is fixed. Overheating will cause them to deteriorate much faster than normal.Allow the engine and exhaust manifold to cool before replacing the exhaust piping. Remove the exhaust pipes from the exhaust manifold. Inspect the manifold for visible signs of damage while the pipes are off. This would be a good time to replace the exhaust manifold gasket. Install the new pipes. The exhaust piping is made of durable black plastic and sold as an individual unit. It is compatible with tillers, chipper shredders, snowblowers, and other small engines manufactured by Cub Cadet, MTD, Troy-Bilt, and Yard Machines.

This part is a carburetor stud. A carburetor mixes fuel and air before delivering it to the engine. The carburetor stud, often called carb stud, is used to ensure a tight seal between the carburetor and the intake manifold. It is important that air and other dirt or debris do not enter the engine, and so this seal between the carburetor and the intake manifold is very important.A carburetor stud may need to be replaced if it is stripped or worn. Of course, a new carburetor stud will be needed if it is missing. If the carburetor and the intake manifold do not have a tight seal, it could be possible that new carburetor studs are needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific carburetor stud is compatible with engines, lawnmowers, and log splitters manufactured by MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt.

The breather hose is designed as a valve or vent that only functions one way. It allows air into the fuel tank but ensures that no air or emissions escape the tank. When this hose is not functioning, emissions and air could be leaking from the tank and cause the engine to perform poorly or not perform at all. The hose could become cracked or damaged, or the ends could lose their seal. Either way, a replacement hose will solve the problem and get the equipment back in order. This genuine OEM replacement breather hose is made by MTD and manufactured to exact specifications. It is compatible with several engines on lawn mowers, snowblowers, and chippers from brands like Troy-Bilt, MTD, Yard-Man, Yard Machines, Bolens, Cub Cadet, and Husky. There are more than 150 compatible machines for this breather hose. This high-quality composite rubber hose is sold individually.