Remington String Trimmer Parts

Starter rope pulls freely without engaging? This pawl assembly restores proper starter engagement with the flywheel on gas leaf blowers and trimmers.

Engine o-ring gasket creates a compression seal between engine components to prevent oil and fluid leaks. Replace when worn or cracked. Verify fit with your model.

O-ring gasket creates a seal to prevent fluid and gas leaks in tillers and lawn equipment. Replace when cracked, brittle, or leaking. Verify fit.

This is an insulator assembly includes the insulator, seals, and hardware. It is designed to create the right spacing between the cylinder and carburetor on many blowers and trimmers made by various manufacturers. The insulator assembly also keeps heat from moving between the other components. Over time, the insulator assembly can become damaged or crack. When this occurs, air can reach the engine and create a condition where the engine can't perform at its best. If this happens, the insulator assembly will need to be replaced. Take off the air filter, drain the fuel, and remove the intake assembly. The insulator can be taken off of the engine before the replacement is added. Use mounting screws to fit the insulator to the other components. Reassemble the other parts to use the tool.This insulator assembly is a genuine OEM replacement part sourced directly from the manufacturer. It is sold as an individual part. This component is made to be used in leaf blowers, tillers, and string trimmers manufactured by Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Bolens, and Yard-Man.

This is a quality rear engine cover that is used on several types of string trimmers. The component is tightened onto the back of the trimer to offer protection and shielding to the engine. It is made of a durable material and comes with both the cover and four screws to attach it to a string trimmer. Over time, the rear engine cover can become damaged, broken, or lost and should be replaced to ensure the engine is protected.Check the rear engine cover for cracks and other damage before installing a new replacement part. First, remove the screws from the rear engine cover so it can be taken off of the string trimmer. An O-ring may be needed to create the proper clearance when installing the new rear engine cover. Make sure to properly tighten the screws on the cover before use.This rear engine cover is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The engine cover is designed to be compatible with string trimmers manufactured by Bolens, MTD, Yard Machines, Murray, and Craftsman.

Flywheel assembly for gas leaf blowers and line trimmers. Mounts to the engine crankshaft. Replace if cracked, damaged, or missing flywheel fins.

Ignition coil module assembly for gas string trimmers. Mounts to engine block and connects to spark plug. Replace if cracked, damaged, or contacts are worn.

Replacement fuel cap for gas trimmers and handheld lawn tools. Seals the fuel tank to keep dirt and debris out. Replace if cracked, missing, or worn.

Replacement throttle trigger spring for gas line trimmers. Installs inside the throttle trigger assembly. Needed when original spring is broken or missing.

This is a bushing made from black plastic with a cleft down the middle to provide enough flex for easy insertion. It has a flanged design, which means it won’t easily pop out after installation, even under stress from constant vibration. The bushing’s primary purpose is to protect wires and cables from damage as they pass through a channel. As such, the material is fairly durable and does not need to be replaced under ordinary circumstances. That said, there are some situations in which it can become damaged. For one thing, it’s easy to damage while repairing the wires or cables that run through the bushing. If the bushing does need to be replaced, it requires disconnecting any cables or wires that run through the bushing. Pop out the old bushing with a rubber mallet, install the new bushing the same way, reconnect the wires, and the repair is complete. This is an OEM part sourced directly from MTD, and it is sold individually. It was initially used on snowblowers but has also been used on lawnmowers and lawn tractors.

Air cleaner cover assembly for gas leaf blowers and trimmers. Protects the air filter from debris. Replace if cracked, broken, or missing clips.

This OEM sprocket assembly contains a sprocket, which is a circular gear with teeth that engage with the links on a chain to move the chain forward.A new sprocket assembly will be needed if the part is broken in any way or if the sprocket teeth are worn off. If it's not immediately obvious to the eye, a test can be performed to determine if a new sprocket assembly is needed. Simply move the chain and if at any point the chain becomes stuck, this means a new sprocket assembly is needed. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This is a genuine MTD part sourced directly from the manufacturer and is sold individually. The sprocket assembly is compatible with trimmers manufactured by either Troy-Bilt or Cub Cadet.

Replacement oil drain plug for outdoor power equipment engines. Installs in the oil pan to seal the drain opening. Replace if stripped, cracked, or leaking.

Protects the air filter on string trimmers from debris and weather exposure. Replace if cracked, broken, or missing to keep filter functioning properly.

Drive belt transfers power to wheels on wheeled trimmers. Replace if worn, cracked, or causing slipping. Verify fit with your model number before ordering.