Roper Dishwasher Parts

• Not drying dishes properly
• Not cleaning dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

• Leaking

I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more

Remove upper and lower baskets for access. Remove 4 Torx screws holding drain/filter assembly, accessing last screw by rotating the water duct clockwise. Be sure to first un-clip the water duct at top and rear of dishwasher so that it can be moved. (Take the opportunity to remove accumulated deposits behind the water duct). Remove the drain/filter assembly and then remove the single screw holding the food chopper housing. Then remove the chopper assembly which is likely to be in pieces if it... Read more

• Not drying dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

• Won't start

Ordered a new thermal fuse from your website last week and installed it three days ago. This is the second fuse in one year that needed to be replaced. The dishwasher was purchased new in 2012. Relatively easy to replace. Your website had a you tube video that showed how to replace it. Power came back on the control panel, but the start button (not a button, but a touch screen) would not work. This is the second time in two years that the control panel had to be replaced because the start... Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

• Leaking

I thought it was the gasket so I ordered a new one. While waiting for it to arrive I read some other forums where I read that sometimes the air vent on the front could be dirty and cause leaking. I popped out that vent cover and it was clogged. Using an old toothbrush and a tiny paint brush I cleaned all of the gunk out. No more leak even with the old gasket in place. I'll save the new gasket for when I need it in the future. Read more

I determined that the gasket was pinched, leaking at corner. Ordered new gasket from this site (easy find with part diagram). Removed old gasket, replaced with new. Read more

• Will not fill with water
• Noisy

Recently my Kenmore dishwasher would start but would not fill with water. A quick test of the float switch reflected proper operation, AND voltage was being delivered TO the contact on the water inlet valve. I then removed power and checked for continuity on the contacts. This read “infinity” (Open circuit) which indicated a break in the coil inside the valve’s solenoid. As such the valve would not open to allow water to flow. I ordered the replacement water inlet valve from... Read more

• Will not drain

I've opened sump housing to check for clogging but it was clean. When I removed check valve to inspect it I've found out that the round part of the valve was missing so I figured it might've blocked the water exit at drain hose or something like that. So I pulled the dishwasher out to get a full access to drain hose connector and the pump. Upon disconnecting the drain and checking its connector I indeed found the round piece totally blocking the hose and acting as a seal. I removed the piece... Read more

My wife said we have a problem with our dishwasher (Whirlpool WDT920SADE2). The dishes were not getting clean, and the soap dispenser opened, but soap was still dribbled down the inside of the door and on the silverware caddy. I'm not the handiest guy; it took me several days to go through the trouble-shooting process, watching multiple videos and trying different things. My initial guess was that the soap dispenser was opening too late. (This turned out to be wrong.) I started off by... Read more

Following the very clear and concise Video from AppliancePartsPros.com, I was able to insert the friction pads that had fallen off from the dishwasher door. It now works. The next project may be to replace the rollers of the Dish Rack which are now a little bit worn out. Read more

• Noisy
• Will not drain

I had previously disassemble the pump assembly to find what I at first thought was an oddly shaped spring, which it was. What I learned by researching the parts was that the spring's odd shape was a result of something having gotten caught in the pump and jamming the impeller. After ordering the parts, I watched the "repair video" a few time and proceeded to remove and replaced the affected parts. Reassembly went pretty much as described with the one small glitch being the seating of the new... Read more

• Not cleaning dishes properly

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more