Roper Dishwasher Parts

The Door Seal is an OEM part for Whirlpool dryers. It forms a tight seal around the dryer door, preventing heat from escaping and ensuring efficient drying performance. This seal helps to maintain the internal temperature of the dryer, optimizing energy use and improving drying results.

Causes of a bad door seal can include wear and tear from regular use, damage due to improper handling or cleaning, or deterioration over time. A compromised door seal can affect the efficiency of the dryer and lead to potential safety issues.

Symptoms of a bad door seal include:

• Heat escaping from the dryer door
• Longer drying times
• Higher energy consumption
• Visible wear or damage to the seal

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Spray Arm Bearing is an OEM replacement part for Whirlpool dishwashers. This supports the rotation of the spray arm, ensuring it can freely move and distribute water evenly throughout the dishwasher during a wash cycle.

Causes of damage to the spray arm bearing can include mineral buildup from hard water, wear and tear from regular use, or damage from debris that has become lodged in the spray arm. 

Symptoms of a bad Spray Arm Bearing include:

• The spray arm not rotating properly or getting stuck, which can lead to dishes not being cleaned effectively.
• Unusual noises coming from the dishwasher, such as grinding or squeaking, indicating that the spray arm is struggling to rotate.
• Poor water distribution inside the dishwasher, resulting in spots or food residue on dishes after a cycle.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Nylon Radial Ring Bearing is an OEM part for Whirlpool dishwashers. It supports the spray arm, allowing it to rotate smoothly and evenly distribute water throughout the dishwasher for effective cleaning. This bearing reduces friction and wear, contributing to the longevity and efficiency of the spray arm mechanism.

You should replace this radial ring bearing if it shows signs of wear, damage, or if the spray arm is not rotating properly. Common causes of a bad bearing include wear and tear from regular use, accumulation of debris, or damage from improper installation or handling.

Symptoms of a bad nylon radial ring bearing include:

• Spray arm not spinning or rotating unevenly
• Noisy operation during the wash cycle
• Reduced cleaning performance
• Visible damage or wear to the bearing

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Upper Dishrack Wheel is an OEM part for Whirlpool dishwashers. This wheel attaches to the upper dishrack, allowing it to slide in and out smoothly along the dishwasher rails. It ensures easy access to the upper rack for loading and unloading dishes, contributing to the overall functionality of the dishwasher.

Over time, the upper dishrack wheel can wear out or become damaged. Causes of a bad dishrack wheel can include frequent use, heavy loads on the dishrack, or accidental damage during loading or unloading.

Symptoms of a bad Upper Dishrack Wheel include:

• The upper dishrack not sliding smoothly or becoming stuck
• Unusual noises when moving the dishrack
• The dishrack becoming misaligned or wobbling

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Inlet Assembly is an OEM part for Whirlpool dishwashers. It is responsible for controlling the flow of water into the dishwasher during the wash cycle. This assembly ensures that the correct amount of water enters the dishwasher to clean dishes effectively.

You should replace the inlet assembly if it becomes faulty. Causes of a bad inlet assembly can include wear and tear from regular use, blockages from debris or mineral buildup, or electrical issues. A malfunctioning inlet assembly can lead to inadequate water flow, which affects the dishwasher’s cleaning performance.

Symptoms of a bad inlet assembly include:

• The dishwasher not filling with water or filling slowly
• Water leaks around the inlet area
• Error codes related to water intake issues
• The dishwasher stopping mid-cycle or not starting

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Inlet Valve Assembly is an OEM part for Whirlpool dishwashers. This valve assembly is crucial for regulating the flow of water into the dishwasher during the wash and rinse cycles.

Common causes include mineral buildup from hard water, wear and tear from frequent use, or electrical issues affecting the valve's solenoid. A malfunctioning valve can lead to improper water levels or no water entering the dishwasher at all.

Symptoms of a bad water inlet valve assembly include:

• The dishwasher not filling with water
• Low water levels during cycles
• Water leaking from the valve
• The dishwasher not cleaning dishes properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Ring Bearing is an OEM part for Whirlpool dishwashers. It is a critical component that supports the rotation of the dishwasher's spray arm, ensuring it can spin freely to distribute water evenly throughout the dishwasher for effective cleaning.

You should replace the ring bearing if it becomes worn out, cracked, or damaged. Causes of a bad ring bearing can include general wear and tear from regular use, accumulation of debris or mineral deposits, and damage from improperly loaded dishes.

Symptoms of a bad ring bearing include:

• The spray arm not rotating properly
• Ineffective cleaning performance
• Unusual noises such as grinding or squeaking during operation
• Loose or wobbly spray arm

This OEM part is also compatible with certain models of Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

The Whirlpool Dispenser Assembly is an OEM component specifically designed for Whirlpool dishwashers. It houses the mechanisms that dispense detergent and rinse aid into the wash basin properly during each cycle.

Causes of a bad dispenser assembly can include clogged or jammed dispenser doors and chutes. Hinges or latches may wear down over years of openings and closings between loads.

Symptoms of a bad dispenser assembly include:

• Liquid detergent or rinse aid dripping outside the dispenser area
• Dishes coming out with residue or spots indicating insufficient cleaning
• The dispenser doors not opening fully or staying shut securely

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Admiral, and select Kenmore models.

The Dishwasher Fuse Kit is an OEM replacement part for Whirlpool dishwashers. It contains the necessary thermal fuses that protect the dishwasher's electrical system from overheating or short circuits. These fuses are critical safety components that help prevent potential fire hazards or damage to the appliance. When replacing this fuse, the included wire harness must be replaced as well.

Symptoms of a blown dishwasher fuse kit include:

• The dishwasher not turning on or powering up at all
• Error codes related to heating or electrical system issues
• Intermittent power failures during wash cycles

Causes of a faulty fuse kit can include electrical surges, wiring problems, component malfunctions leading to overcurrent situations, or simply wear and tear over time.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Spray Arm Nut is an OEM replacement part for Whirlpool dishwashers. This nut secures the spray arm to the dishwasher, ensuring it stays in place while distributing water to clean dishes effectively.

The spray arm nut can become worn out or damaged due to regular use, exposure to high water pressure, or accumulation of debris. Over time, it may loosen or crack, affecting the spray arm's performance.

Symptoms of a bad spray arm nut include:

• The spray arm not rotating properly
• Water not being distributed evenly during the wash cycle
• The spray arm detaching from its mount
• Noisy operation or rattling sounds

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rack Adjuster is an OEM part for Whirlpool dishwashers, designed to allow for the easy adjustment of the dishwasher rack's height. This feature accommodates dishes of various sizes. By providing the flexibility to adjust the rack height, this part enhances the dishwasher's adaptability to different washing needs.

Symptoms of a failing Rack Adjuster include:

• Difficulty in adjusting the dishwasher rack's height
• The rack becoming loose or detaching from the adjuster
• Visible wear or damage to the adjuster components

Causes of a bad Rack Adjuster can range from normal wear and tear, which gradually degrades its components, to accidental damage during loading or unloading of dishes. 

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Detergent Lid Spring is an OEM part for Whirlpool dishwashers. It is responsible for providing the necessary tension to open and close the detergent dispenser lid during the wash cycle. 

Over time, the detergent lid spring can wear out, lose tension, or break due to repeated use, exposure to water and detergent, or accidental mishandling. If the spring becomes faulty, the dispenser lid may not function properly, leading to poor washing results.

Symptoms of a bad detergent lid spring include:

• Detergent dispenser lid not opening during the cycle
• Difficulty in closing the dispenser lid
• Inconsistent or incomplete release of detergent
• Visible damage or wear on the spring

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

For the complete detergent dispenser kit order 4387043.

The Upper Dishrack Wheel Assembly is an OEM part for Whirlpool dishwashers. This assembly helps the upper dishrack glide smoothly in and out of the dishwasher for easy loading and unloading of dishes.

Causes of a bad Upper Dishrack Wheel Assembly can include wear and tear from regular use, accumulation of dirt or debris on the wheels, and damage from accidental impact or heavy loads.

Symptoms of a bad Upper Dishrack Wheel Assembly include:

• Difficulty sliding the upper rack in and out
• Noisy operation when moving the rack
• Rack becoming misaligned or falling off the tracks
• Visible damage or wear to the wheels

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: White. Size: 13 oz can. Acrylic appliance aerosol can spray paint.

The Appliance Spray Paint is an OEM part for Whirlpool appliances, designed to provide a quick and effective way to touch up or completely refinish the exterior of various appliances. This specialty spray paint is formulated to adhere to metal surfaces, offering a durable and resistant finish that can withstand the routine wear and tear of kitchen environments, including heat, moisture, and everyday use.

The primary reason for using such a specialized paint is to maintain or restore the aesthetic appeal of your appliances while protecting them from further damage. 

Symptoms needing for Appliance Spray Paint include:

• Scratches, chips, or rust spots on the appliance's exterior that can lead to further damage or corrosion if left untreated
• A desire to refresh or update the appearance of the appliance without the need for complete replacement
• Discoloration or fading of the original finish due to age, exposure to sunlight, or cleaning agents

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Water Inlet Valve is an OEM part for Whirlpool dishwashers, designed to control the flow of water into the appliance. This valve is crucial for ensuring that the dishwasher fills with the correct amount of water at the right time during the cleaning cycle. It is made with precision to match Whirlpool's stringent quality standards, guaranteeing reliability and efficiency.

Causes of a bad Water Inlet Valve can include mineral deposits blocking the valve, wear and tear over time, and electrical failure that prevents the valve from opening or closing properly. Such issues can lead to problems with the dishwasher's performance and efficiency.

Symptoms of a malfunctioning Water Inlet Valve include:

• Dishwasher not filling with water
• Overfilling, leading to potential leaks
• Unusual noises during the fill cycle
• Erratic cleaning results due to improper water levels

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Note: Due to design changes, adapter part number W10685193 may be required for your repair.

The Impeller is an OEM part for Whirlpool dishwashers. It plays a crucial role in the dishwasher's operation by creating the water pressure needed to circulate water through the spray arms, ensuring dishes are thoroughly cleaned during the wash cycle.

Over time, the impeller can become worn or damaged due to regular use, the presence of debris, or exposure to harsh detergents. This can result in decreased water pressure and ineffective cleaning.

Symptoms of a bad impeller include:

• Poor cleaning results with dishes remaining dirty
• Unusual noises coming from the dishwasher
• Low water pressure or weak spray from the spray arms
• The dishwasher not completing its cycle properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.