Roper Washer Parts

This retaining clip secures small panels and components to help keep assemblies aligned and reduce rattles or movement during operation. It's a simple replacement that restores proper fit where the original clip has broken or gone missing. What it does:

• Holds trim, panels or small assemblies in place to prevent loosening and vibration
• Restores proper alignment and fit where a worn or broken clip causes gaps or rattling
• Commonly used where snap-in retention is required for plastic or sheet-metal parts
• Simple, single-piece part with no electrical or mechanical adjustments needed

• One retaining clip

• Turn power off and unplug the appliance before accessing the repair area
• Remove any adjoining panels or fasteners as needed to access the clip location
• Press or snap the clip into the mating slot; use care to avoid bending surrounding parts

This pushbutton switch restores a single button on the appliance control panel so you can reliably send selection or command inputs to the control board. It replaces a worn, stuck or non-responsive panel button. What it does

• Acts as the user-facing pushbutton that completes the control input circuit when pressed
• Sends selection/command signals to the appliance control board or timer
• Common symptom fixer: button that won't register presses or responds intermittently
• Also used when a button is physically stuck, loose, or missing

• Disconnect power to the appliance before beginning service to avoid shock
• Access typically requires removing the control panel or overlay—retain screws and trim
• Verify connector orientation and seating; do not force connectors or terminals

Sealer for refrigerant line insulation.

This drain hose coupling kit connects the washer drain hose to the appliance drain outlet, restoring a secure, leak-resistant hose connection and preventing water leaks during drain cycles. What it does:

• Provides a replacement coupling to join the drain hose to the washer drain outlet
• Re-establishes a tight hose connection to reduce leaks and water damage
• Addresses symptoms such as leaking at the drain connection or a loose hose fit
• Compatible with affected Whirlpool top-load washer drain assemblies

• Unplug the appliance before servicing and work on a dry surface
• Remove the old coupling and inspect the hose and outlet for damage before installing
• Ensure the hose is fully seated and secure with the existing or supplied clamp(s)

These replacement 6" FXF vacuum bags capture dust and debris to restore pickup performance and keep the appliance's airflow and motor compartment cleaner. Designed as a direct-fit consumable for compatible bagged upright and canister vacuums. What it does:

• Collects dirt, dust and debris so particles stay contained for easier disposal
• Helps maintain suction by keeping the vacuum's intake and motor chamber clearer
• Reduces dust and allergen re-distribution compared with a torn or overloaded bag
• Replaces worn or full bags that cause reduced capacity, visible dust escaping, or increased odor

• Always unplug the vacuum before removing or installing bags
• Remove the full bag carefully to avoid spilling debris; seal and dispose per local regulations
• Verify correct orientation and secure fit before operating to avoid leaks
• Replace bags regularly; inspect the inlet collar and seals for wear when servicing

This is a replacement mounting screw used to secure appliance panels and components. It restores proper fastening so panels and parts stay aligned and stable during normal use. What it does:

• Fastens appliance panels, trim or internal components in place
• Replaces missing or stripped screws that cause rattling or loose parts
• Helps stop panel vibration and maintain proper component alignment
• Matches OEM fit where specified for a secure installation

• One replacement mounting screw

• Verify screw size and fit before installation; use the correct screw location from your parts diagram
• Turn off and disconnect power to the appliance before accessing internal components
• Hand-start the screw to avoid cross-threading; tighten until snug—do not over-tighten
• Wear safety glasses and follow manufacturer service instructions when applicable

Size: 1/4 lb.

This replacement door strike provides the solid catch point the latch/lock grabs so the appliance recognizes the door or lid is closed and can run safely. A worn, bent, or broken strike can interrupt operation. What it does

• Forms the fixed catch for the door/lid latch or lock
• Helps actuate the interlock/safety switch so a cycle can start
• Misalignment or damage can keep the door from latching and stop cycles
• Common symptoms: door/lid won't latch or stay closed, unit won't start, "Door/Lid" or "Lock" message, needing to hold the door shut, visible cracks or wear on the strike

• 1 strike

• Disconnect power to the appliance before servicing
• Open the door/lid and remove the mounting screws securing the old strike; retain hardware if it is reused
• Position the new strike in the same orientation and tighten screws snugly; avoid over-tightening to prevent damage
• Close and open the door/lid to confirm smooth latch engagement, then run a brief test cycle

This leveling foot threads into the base of your appliance to support and stabilize it. Adjusting the foot helps level the cabinet, reduce wobble and vibration, and keep doors aligned for smooth, reliable operation. Also called a leveling leg. What it does:

• Provides an adjustable contact point to stabilize the unit on the floor
• Helps level the cabinet so doors align and seal properly
• Reduces rocking, rattling, or excessive vibration on uneven surfaces
• Replaces a cracked, stripped, or missing leveling leg

• 1 leveling foot

• Unplug the appliance and turn off water supply if applicable
• Use a helper to carefully move or tilt the unit; support it securely
• Unthread the damaged foot; thread in the new foot by hand, then fine-adjust with a wrench
• Level side-to-side and front-to-back; ensure all feet make firm floor contact

This replacement light bulb restores visibility inside your appliance so you can quickly see food, settings, and contents. Replace a burned-out or flickering bulb to bring back bright, reliable illumination in compatible models. What it does:

• Provides interior light when the door is opened or the light switch is activated
• Directly replaces a failed, dim, or intermittently flickering bulb
• Helps you see items and controls clearly during use
• Common signs you need this part: light won't turn on, flickers, is very dim, or the bulb is visibly damaged

• 1 light bulb

• Disconnect power (unplug the appliance or switch off the circuit breaker) before starting
• Allow the old bulb to cool completely to avoid burns
• Remove any lens or cover as your model requires; carefully remove the old bulb and handle the new bulb with a clean cloth or gloves
• Do not exceed the bulb type/wattage specified for your model; restore power and test the light

This balance ring mounts on the top of the washer's spin basket. Its sealed, liquid-filled chamber shifts weight to counterbalance uneven loads so the tub spins smoothly, reducing vibration, noise, and stress on other components. What it does:

• Uses internal fluid to counterbalance heavy or uneven loads during spin
• Helps minimize vibration, shaking, and thumping noises
• Reduces washer movement or "walking" during spin
• Common failure symptoms: excessive vibration/noise, frequent out-of-balance loads, or visible cracks/leaks at the ring

• 1 balance ring assembly

• Disconnect power and water; wear gloves and use proper safety precautions
• Access the ring by removing the cabinet/top and inner basket (procedure varies by model)
• Remove the old ring; seat the new ring evenly on the basket rim—do not puncture the sealed chamber
• Reassemble, level the washer, and run a test spin to ensure smooth operation

Restore dependable cycles with this replacement timer. It controls the sequence and duration of each step, sending power to the correct components at the right time so the machine advances smoothly from start to finish. What it does:

• Directs power to components to run each cycle segment in order
• Advances the cycle through preset intervals
• Helps resolve cycles that won't start or won't advance
• Addresses stopping mid-cycle or only running on certain settings
• Can help when the timer dial doesn't move or advances intermittently

• 1 timer

• Disconnect power before servicing; turn off water supply if applicable
• Access the control console; remove the knob/escutcheon if required and unmount the timer
• Transfer wires one at a time to the new timer or use a photo to match positions
• Reassemble and run a short test cycle to proper operation

This touch-up paint restores small chips, scratches and nicks in painted appliance surfaces for a cleaner, like-new appearance. It's ideal for hiding minor cosmetic damage without repainting the whole panel. What it does:

• Covers small chips, scratches and scuffs on painted appliance surfaces
• Helps prevent bare metal exposure that can lead to rusting of small areas
• Restores color and gloss to localized damage for improved appearance
• Applies to control panels, doors and trim where finish is worn

• Shake well before use and apply sparingly with a fine brush, cotton swab or toothpick
• Allow finish to dry fully between light coats for best color match
• Work in a well-ventilated area and avoid inhaling fumes
• Keep out of reach of children and follow local disposal regulations for paint

This agitator replaces the top agitator in compatible top-load washers to restore proper fabric movement and cleaning action. It helps re-establish the washer's normal wash motion and reduces poor wash performance caused by a damaged agitator. What it does:

• Replaces a cracked, worn or broken top agitator to restore wash motion and even water circulation
• Helps fix symptoms such as clothes not tumbling, uneven cleaning, or excessive vibration during the wash cycle
• Transfers torque from the transmission to move clothes through the wash water
• Works with the factory agitator coupler/bolt and transmission components when installed correctly

• One top agitator assembly

• Disconnect power and water supply before beginning any repair
• Remove the fabric softener dispenser and the agitator cap to access the retaining bolt
• Tighten the retaining bolt to the manufacturer's specified torque and confirm proper engagement with the cam/coupler