Dishwasher Shelf Support Stud Parts

I discovered that the manifold was not connecting with the water supply,so the dishes in the upper tray were not being washed. This was caused because the rear hanger on the manifold had broken and it did not lineup properly into the water supply connection in the back of the dishwasher. I removed the manifold and found that it had two part numbers stamped on it. I searched on both part numbers and received a hit on the second part number. The photo looked exactly like my manifold so I... Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more

Replaced the right and left front upper dish rack wheels. The best part was I ordered the parts Monday and had them first thing Tuesday morning. Read more

Replaced the entire Drive set, even the motor that was not broken. The six quart 6000 HD is running like new. We broke it, your parts fixed it. Of course takes a little know-how on our part as well. Thank you! Read more

1, Removed roller tray front stoppers from each side. 2. Pulled out empty top rack from dishwasher. 3. Removed existing top rack roller. 4. Inserted new roller where old one was located. 5. Repeated for each roller. 6. Inserted top rack back into dishwasher. 7. Enjoyed using both racks again!! Read more

Ordered parts Read more

The vertical shaft showed a slight bend so I replaced the bent shaft with a new shaft. I should have done that when I was replacing the gears. Although we have not mixed any more bread, I ran the mixer at a both low and high speeds for several minutes without any more gear clashing noises. It now purrs ! The top bearing on the original vertical shaft had slipped down the shaft when I first examined it. This may have been the source of all of my problems with this mixer. It may have been... Read more

Chopper screen was completely blocked. Chopper blades separated from the shaft. Retainer ring came off of the shaft but was able to re install the chopper assembly. Worked fine after cleaning the screen and reassembly the lower spray arm. Lower spray arm hub tab broke when removing so purchased a new one with a new bearing. Appliance Part Pros video was excellent and very helpful. Read more

No tools required. One item was defected but Appliance parts replaced it immediately. Read more

Replaced the tracks. You need to pull the dishwasher out for this since the screws holding them are on the outside. Not super complicated in my case since my dishwasher didn't require disconnecting water hose or power wires to pull out (there was enough slack behind). Read more

I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more

Replaced complete roller- screw,wheel and axel. Easy job Just recently I had to replace upper spray arm. I ordered assembly from you and was completely satisfied with your service and price, that was over 1/2 of what local appliance repair dealer wanted. Very satified with how to do video on this project Read more

Replaced dishwasher spray arm, spray arm support plate, dishwasher drain trap filter assembly. Read more

The lower basket L& R track bearing brackets on my KitchenAid dishwasher (KDTE704DSSO) finally gave out (ball bearings everywhere) after (6) years of daily, family use. The service techs provided me with all the information I needed to successfully and quickly complete my project. My parts were mailed to me very quickly and my dishwasher was up and running in short order. The parts were clean and in perfect working condition. (After pulling your dishwasher out, there are two sets of screws on... Read more

Thanks to Appliance Parts Pros, who took the time and made the effort, they found me a replacement part for my dishwasher. Read more

Removed the bottom rack from the dishwasher. Removed the 2 front plates at bottom of the dishwasher. Removed the two screws from the top of the dishwasher holding the dishwasher to the counter-top. Pulled the dishwasher out. Removed the 8 mm screws from the outside of the dishwasher-- 4 per side (Underneath the sound proofing). Pulled the old tracks and placed the new tracks into place and tightened the screws back up. Pushed the dishwasher back into place. Reinstalled the screws securing... Read more