Microwave Hardware Hand Small Engine Safety Switch Parts

The Range Screw is an OEM part for Whirlpool ranges. It is a small but essential component used to secure various parts and panels of the range. It is designed to fit securely into pre-drilled holes, holding components tightly in place.

There are a few factors that can lead to a bad Range Screw. Over time, screws may become loose or stripped due to frequent use or inadequate tightening. Accidental cross-threading or overtightening can also damage the screw or the surrounding components.

Symptoms of a bad screw may include loose or wobbly parts, rattling noises during operation, or difficulty in keeping components securely attached. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Microwave Monitor Switch is an OEM part for GE microwaves. This part monitors the position of the microwave door, ensuring that the microwave does not operate when the door is open. It acts as a crucial safety feature, preventing the microwave from emitting radiation when the door is not securely closed.

Causes of a bad monitor switch can include general wear and tear, repeated use, or electrical issues.  

Symptoms of a bad monitor switch include:

• Microwave not starting or running intermittently
• Microwave operating with the door open
• Error codes or safety warnings displayed
• Unusual noises or sparking inside the microwave

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

For mounting also consider WPW10269225 mounting plate

The Hardware Kit is an OEM part for Whirlpool microwaves. This kit includes essential mounting brackets, screws, and other fasteners required for the proper installation and secure mounting of the microwave, either over the range or within cabinetry.

Causes of a bad hardware kit can include wear and tear over time, exposure to moisture, or damage due to mishandling or incorrect installation.  

Symptoms of a bad hardware kit include:

• Loose or unstable microwave installation
• Rattling or vibrating noises during operation
• Difficulty in mounting or securing the microwave
• Visible rust or damage to screws and brackets

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

15 Amp, 125/250 Volt. Package of 2. Switches have 3/16 inch terminals.

The Microwave Mounting Nut Assembly is an essential component for securing your microwave in place. Designed specifically for Samsung microwave models, this genuine OEM part ensures a perfect fit and reliable performance. The durable construction of the ASSEMBLY HOLDER-NUT provides strong support, keeping your appliance stable and safely mounted. Installing this mounting nut assembly is straightforward, allowing you to restore your microwaveGÇÖs functionality without hassle. Whether you are replacing a worn-out part or repairing a damaged mount, the Microwave Mounting Nut Assembly offers a dependable solution. Using a genuine OEM part guarantees compatibility and maintains the integrity of your microwave, preventing potential issues from inferior replacements. This assembly holder-nut not only enhances the safety of your kitchen setup but also contributes to the overall efficiency of your appliance. Trust in the quality and precision of the Microwave Mounting Nut Assembly to keep your microwave securely in place and operating smoothly for years to come.

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

This door release lever connects the push-button to the latch assembly inside the microwave. Replacing a worn lever restores smooth, reliable door opening so the button works on the first press.

• Transfers motion from the door-open button to the latch hooks to release the door
• Helps resolve a door that won't open when the button is pressed
• Addresses a button that feels loose, sticks, or lacks resistance
• Replaces a cracked or broken lever causing intermittent door operation

• Unplug the microwave and discharge the high-voltage capacitor before servicing
• Remove the grille and control panel to access the interlock/latch area
• Note spring and pivot orientation and transfer any reusable hardware
• Test door release action before completing reassembly

This microswitch senses the microwave door position and controls the safety interlock circuits. Replacing a worn switch restores proper start/stop behavior so the oven only runs when the door is fully closed.

• Detects door open/closed status to enable or disable cooking
• Part of the safety interlock system that stops operation if the door opens mid-cycle
• Replace if the switch fails a continuity check or shows heat or terminal damage

• Disconnect power before service; microwave capacitors can retain a dangerous charge
• Note wire positions and move them to the same terminals on the new switch
• Ensure the door latch cleanly actuates the switch; test operation before reassembly

This replacement screw secures appliance components so panels, brackets, and assemblies stay tight and aligned. Replace stripped or missing hardware to eliminate rattles and keep your unit assembled safely and correctly.

• Fastens panels, brackets, or components to the appliance frame
• Restores a secure fit when the original screw is lost, stripped, or corroded
• Helps prevent vibration noise and movement during operation
• Supports proper alignment of trim and assemblies

• Disconnect power; for gas units, also shut off the gas supply
• Use the correct driver to avoid stripping the head; do not overtighten
• Inspect and address damaged mating threads, clips, or brackets before reinstalling
• Refer to your model's parts diagram to confirm location and quantity

Includes 12 washers.

This mounting nut kit secures a threaded connection or component inside your appliance, keeping it tight and stable during operation. Replacing a worn or stripped nut restores a solid hold and helps prevent leaks, rattling, and poor performance. What it does:

• Fastens a component or fitting to its mating surface, maintaining proper alignment
• Restores grip when original threads are stripped, cracked, or worn
• Helps prevent vibration-related loosening during cycles
• Can resolve symptoms such as a loose/wobbly assembly, rattling noises, seepage at the joint, or visible thread damage

• One mounting nut kit

• Disconnect power; shut off water supply if the joint carries water
• Support the mating component while installing to avoid strain on plastic parts
• Start threads by hand to prevent cross-threading; tighten only until snug—do not overtighten
• Inspect any related gasket/O-ring and replace if worn or damaged

The Installation Hardware Kit is an OEM part for GE over-the-range microwaves. It contains brackets and fasteners used to securely mount the microwave above the range cooking surface.

Symptoms requiring an installation hardware replacement include:

• Missing or damaged anti-tip brackets  
• Loose mounting screws or damaged mounting plates
• Inability to properly position and affix the microwave

Causes can be stripped mounts from over-tightening old hardware or components lost during a previous removal. Normal wear over extended use may also degrade hardware.

This genuine GE kit is compatible with some Profile and GE Profile series models as well.

The Nut is an OEM part for Whirlpool microwaves. It helps secure various parts within the microwave, ensuring proper assembly and function. It is used to fasten items, keeping them securely in place during use.

A bad microwave nut can occur due to wear and tear over time or accidental damage. If the nut becomes loose, stripped, or misplaced, it can lead to instability and compromise affected parts.

Symptoms of a bad microwave nut include:

• Loose or wobbly parts.
• Difficulty in operating the microwave.
• Unusual noises or vibrations during use.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This flat bolt is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded bolt to restore a tight, secure assembly and help prevent loosening, rattling, or misalignment during normal operation.

• Fastens panels, brackets, and other components as designed by the manufacturer
• Restores a secure fit when the original hardware is missing or damaged
• Helps reduce looseness and vibration-related noises
• Built to original specifications for proper fit and function

• Disconnect power and allow the unit to cool before servicing
• Support the part being fastened; align holes before inserting the bolt
• Start threads by hand to avoid cross-threading; tighten securely without overtightening
• Reuse any original washers or spacers if present