Washer Clock Timer Motor Parts

The error code implies a faulty fill valve. This was not the case for me. Replacing the main PCB assembly solved the problem. I have run two full loads since the repair with no problems. Read more

Took out old timer, and upon inspection notice some electrical arcing( burned areas). I installed new timer and worked perfectly. Problem was that it would fill up with water, but after it was filled the timer kept going but washer was not agitating. Only thing that worked was delicates wash. Important Disconnect/ unplug power cord! 1. Remove knob, center cap pops off revealing a pin. Slide that off and the knob should come off. 2. Removing knob should reveal 2 socket screws remove... Read more

My Kenmore washer had three problems and thanks to AppliancePartsPros.com videos I was able to repair all three. The washer coupler was defective so I replaced it. This topok about 30 minutes. The washer lid switch was defective. This took about an hour. Finally, the motor was defective. I was able to disconnect the motor from the transmission and test the motor by leaving the wiring connected and run a wash cycle. The motor was dead. I replaced it with a new motor and now the washer runs... Read more

Started out as a replacement of the coupling between the motor and the basket transmission ( 2 of the 3 legs on the transmission side broken.. )... Bought a new pump, since I would have it off... or so I thought.. Metal output shaft into pump + years of moisture = pump rusted on. Put it all back together - runs fine... for a while.. Then the old pump bearings burn out. Back apart.. Cut the old pump off the motor. Reinstall everything... Nothing, Just sits there and buzzes... Now... Read more

Easy. Opened the front panel, removed the timer, went on line with the part number. Part arrived the next day and I installed it in 2 minutes. FIXED. Read more

The basin would fill but would not agitate, there was no sound, no grinding noises, no sound of a motor running without agitation due to a broken belt. The basin full of water was able to drain if I advanced the timer to Spin. By playing around with the timer dial further, I could get every function of the washer to operate, at least partially. So, that said electrical problem to me. I assumed the trouble was either the safety switch at the back of the lid or the timer mechanism. Tested... Read more

This is the second time this issue has come about. Bosch would tell you that you have a brushless motor. This is not true. If you get on youtube.com you can see how you can replace the brushes in your motor. Brush replacement. $50. New motor using a appliance repair man $500. Read more

Replaced drive hub , drive clutch kit , & drive motor Read more

My experience could not have been smoother. I called the repair guy just to see how much money I saved and I was shocked! I saved $123.00, thanks to appliance parts pro. Thank you so very much for your professional help, great prices & super fast shipping! From now on, when another appliance needs repair I'm going to you guys first. I'm spreading the word to every single person I know and posting it on social media as well. Thanks again, Jeremy Read more

Checked circuit breaker to d/w first. Good. Went to website to see no power issues. Most all of them mentioned the noise filter being the problem. Removed filter from machine and found the corner melted where fuse is located. Ordered new filter, installed, and now have power to switches. All the information I found on the website really made this a easy job to get done. Read more

After unplugging the washer from the electrical outlet, the top of the washer was removed without a problem in order to allow easy access to the Central Control Unit (CCU) at the top of the back end of the washer. A cell phone was used to photograph the wiring layout and connectors plugged into the CCU, and then all connectors and the harness were carefully removed from the CCU without incident. Attempting to remove the old CCU, the plastic retaining clips built into the old CCU housing broke... Read more

Technician wanted $700. I was able to fix it myself for around $300 in about a half hour with the great and helpful customer service of appliancepartspros.com. Parts arrived on time. Nice to know there is a company that really cares and they know there stuff. Read more

Got help from the internet to diagnose the problem. Seens that the neutral drain part of the transmission will not shift to spin unless there is a pause after draining. Thought the problem might be in the transmission but found the timer wasn;t allowing a pause after draining.therefore the machine would not spin. Replaced the timer and problem was solved. Thanks for your help, Jerry w. Read more

I watched videos on the website and took it apart. Put new motor on, also I put new belt even though the original belt was still ok, but I saw a little sign of shredding ...and there! !! It works like brand new washing machine. . Thanks to appliancepartspros.com...It made save a lot of money by doing it myself.. Read more