Washer Slow Clamp Snowblower Spark Plug Parts
Genuine Lg part
By: Lg
Part Number: ACA56078801
Secures the outer door boot seal to prevent water leaks. Replace if damaged, rusted, or losing tension. Includes tensioning spring. Verify fit.
Do-It-Yourself Stories from Customers like You
LG front load washer door gasket needed replacement due to mold buildup Howard F. • Port Orange , FL • April 15, 2020
If you have an older model WM8000H_A you MUST pay attention to the type of door gasket (boot seal) that it uses. Every video I could find for replacing the seal on the WM8000HWA involved a different product than what was required for our specific washer. I wound up getting the wrong one by ordering it without help and had to exchange it - after I had the machine taken apart. Thanks to AppliancePartsPros I got the correct seal and front retaining ring the next day.
NOTE! The retaining rings are...
Read more
More
Genuine Ge part
By: Ge
Part Number: WH1X2117
Secures the timer knob to the shaft for accurate cycle selection. Replace if worn, broken, or lost causing knob to spin freely. Confirm fit with model.
Do-It-Yourself Stories from Customers like You
The control knob spun freely without engaging to select cycle Polly H. • Glen Allen , VA • November 11, 2014
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle.
https://www.youtube.com/watch?v=cQwLtRcHx9k
Read more
More
Genuine Lg part
By: Lg
Part Number: 2W20017E
Secures the outer door gasket to prevent water leaks during wash cycles. Replace if rusted, corroded, or the seal isn't holding tight. Confirm fit with model.
Do-It-Yourself Stories from Customers like You
Washer basket was loose banging/knocking when running eventually gave a 'load out of balance code" Dwayne D. • Hopewell Junction , NY • September 29, 2014
The repair was fairly straight foward as shown in the video. However, driving the shaft from the bearings took some doing. It required replacing the use of the board with a spare bolt and a 2lb hand sledge. (having an air hammer as reserve, also not a bad idea) I rated this reair as a "1" however I've been an auto mechanic for 40 years. If you do not have good general mechanical ablities you may find this more challenging as you get it further apart. I suggest anyone making this repair should...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 285790
The Clutch Band and Lining Kit is an OEM part for Whirlpool washing machines. It contains the clutch band and clutch lining components essential for proper transmission of power from the washer motor to its drum during the spin cycle. The clutch band and lining allow for a controlled amount of slippage to safely extract water from clothes without damage.
Symptoms of a bad clutch band and lining include:
- Excessive noise or vibration during spin
- Slow or ineffective spinning
- The drum failing to spin or “locking up”
- Premature wear of other transmission parts
Over time and with heavy use, these components can wear down. If slipping or damage is detected, it’s important to replace the kit to avoid potential transmission repairs.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Spins slowly
-
Will not agitate
-
Pumps but will not spin
See more...
Do-It-Yourself Stories from Customers like You
Squealing during spin cycle and very weak agitation Elijah S. • Stockton , CA • May 24, 2015
My parents have the older 80 series washer and dryer that gets used way more than a consumer washer and dryer was ever meant to be used. The washing machine finally said im tired. During the spin cycle it was making a really loud squealing noise and during the agitation cycle it would barely agitate the clothes. So i ordered the basket drive to get rid of the squealing during spin cycle and noticed the dogs on the cams were warn and werent grabbing so ordered the whole cam kit to be safe...
Read more
More
Genuine Ge part
By: Ge
Part Number: WH16X513
The Drain Hose Clip is an OEM part for GE washing machines. It secures the drain hose to the back of the washer, preventing it from becoming dislodged during operation. This ensures that water is properly directed out of the washer and into the household drain system, preventing leaks and water damage.
Causes of a bad drain hose clip can include wear and tear from regular use, damage from improper handling during installation or maintenance, or breakage due to repeated stress and movement of the washer.
Symptoms of a bad drain hose clip include:
- Water leaking from the back of the washer
- Drain hose detaching or becoming loose during operation
- Difficulty securing the drain hose in place
- Visible damage or cracking on the clip
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Note: For the entire drain hose, use part number WH41X10096.
Do-It-Yourself Stories from Customers like You
Discharge hose for 15 year old hot point washer Edith P. • Shelton , CT • October 06, 2014
The fix was so easy 2 screws and done, the part i ordered came the following day, i didnt expect it to arrive for another 3 to 4 days, excellent service , shipping, recieved the correct parts, and they have everything in stock, i would recommend Appliance Parts Pros to everyone, you wont be let down, believe me, thank you for the fast service, i give them 10 stars,
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 285868
Seals filter housing to prevent leaks and maintain proper water flow in your washer. Replace if missing, cracked, or causing leaks. Verify fit by model.
Do-It-Yourself Stories from Customers like You
Whirlpool lsr7233eq0 washing machine was leaking out the bottom Jerald F. • Laud Lakes , FL • April 05, 2015
I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596669
The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.
Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Leaks at the hose connection points
- Hoses slipping off the connections
- Visible rust or damage on the clamp
- Reduced appliance efficiency due to leaks
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not stop filling with water
-
Leaking
See more...
Do-It-Yourself Stories from Customers like You
My washing machine smelt horrible Bryan W. • Ogdensburg , NY • August 20, 2018
First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available....
Read more
More
Genuine Ge part
By: Ge
Part Number: WH02X10093
The Compression Ring is an OEM part for GE washing machines. This ring is essential for securing the tub within the washing machine, ensuring it remains in place during the wash and spin cycles. It helps maintain the stability and proper function of the washing machine.
You should replace the compression ring if it becomes worn, cracked, or damaged. Causes of a bad compression ring can include frequent use, high-stress loads during wash cycles, or physical damage, which can lead to instability and poor washing performance.
Symptoms of a bad compression ring include:
- Excessive shaking or movement of the washing machine during cycles
- Unusual noises during operation
- The washing machine tub appearing misaligned or loose
- Ineffective washing due to instability
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The timer switch came detached from the bracket and the dial slot slipped out of the shaft until i saw the repair video i did not know about the clip that locks the dial to the shaft Jeffery B. • Donalsonville , GA • September 04, 2015
I removed the dial knob and plate as instructed by the video, removed the front panel of the washer to access the switch. I found the plastic molded bracket that the timer rests on to be broken and the tab on the timer where it is attached by a screw to be broken. I ordered a replacement switch, dial and knob. When it arrived I replaced the parts as instructed, but I had to use super glue to hold the new switch in place due to the support tab on the washer panel being broken off. After letting...
Read more
More
Genuine Lg part
By: Lg
Part Number: 4861ER2001D
Secures the inner door gasket to prevent water leaks during wash cycles. Replace if gasket is loose or leaking. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Lg washer/dryer combo unit shook upper counter balance weight loose damaging the mount lugs on the tub cover and tore the tub gasket Christine V. • Saluda , VA • March 28, 2020
The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 134616300
Secures hoses and boots to pumps and tubs, preventing leaks. Replace if damaged, rusted, or unable to tighten. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
E21 water not pumping out fast enough (eiflw55hmb washer) Helmut D. • Rancho Palos Verdes , CA • April 20, 2020
Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP285655
The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.
Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.
Symptoms of a bad hose clamp include:
- Water leaks around the hose connection points
- The hose slipping off the fitting
- Visible rust or wear on the clamp
- Difficulty in tightening the clamp to secure the hose
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Syphonbreak was leaking James O. • Bryant , AL • September 04, 2015
We ordered parts from appliance parts pros and I fixed it.
Read more
More
Genuine Ge part
By: Ge
Part Number: WH01X10279
Secures the door boot seal to prevent water leaks in front-load washers. Replace if rusted, broken, or boot becomes loose. Verify fit with your model.
Do-It-Yourself Stories from Customers like You
Leaking rubber gasket GE washer model no: wpdh8800j3mg Michael C. • North Truro , MA • January 22, 2024
I replaced the following parts in the GE WASHER that I have owned for approximately 14 years:
Part no.: WH08X10038 - rubber gasket
Part no.: WH01X10277 - inside gasket clamp
Part no.: WH01x10279 - outside gasket clamp
The two gasket clamps were ordered on 1/18/24 and delivered the next afternoon to my front door. I already had the replacement rubber gasket from a long time ago.
I will mention that I have NEVER tried replacing a part on a major appliance. Since the washer machine is 14 years...
Read more
More
Genuine Lg part
By: Lg
Part Number: 4861FR3068A
The Clamp is an OEM part for LG washing machines. It is used to secure the hose connections within the washer, ensuring that water flows correctly without leaks.
Over time, the clamp can become worn or damaged due to repeated exposure to water, vibration, or general wear and tear. If the clamp fails, it can lead to water leaks or hoses becoming detached.
Symptoms of a bad clamp include:
- Water leaking from hose connections
- Hoses coming loose or detaching during operation
- Visible rust or damage on the clamp
- Poor water flow or pressure issues
This OEM LG part is also compatible with Sears/Kenmore models.
Do-It-Yourself Stories from Customers like You
Bad bearings seal and spider David R. • Jacksonville , FL • February 04, 2017
If your LG Front load washers sounds like a freight train, STOP USING IT. You're doing more damage and will need more parts to fix it.
After the noise became unbearable, I began to explore and disassemble. I knew enough to know the bearings must be bad but had never done this repair before. ( I am however pretty mechanically inclined.)
Watch this video before you start tearing your LG apart. APP did a great job explaining the steps of the repair. Do a search on this site or youtube.com with...
Read more
More
Genuine Lg part
By: Lg
Part Number: 4930FR3040A
Supports suspension springs that stabilize the washer drum, reducing vibration and noise during operation. Replace if drum shakes excessively or hits sides. Verify fit with your model number.
Do-It-Yourself Stories from Customers like You
Lg washer was rocking really badly and the drum was hitting the sides during every spin cycle and even coming off the top spring mount Benjamin M. • Lynchburg , VA • January 18, 2016
Replaced all three dampers and then replaced locking gaskets for the top spring mounts for the drum, replaced the old feet pads I had and works like a charm!
Read more
More
Genuine Bosch part
By: Bosch
Part Number: 00439671
Secures the door boot seal to the washer front panel, preventing leaks. Replace if broken or when installing a new door seal for proper fit.
Do-It-Yourself Stories from Customers like You
Leaking washing machine replaced rubber door boot.. Gerhard P. • Dagsboro , DE • November 04, 2019
Fixing was easy and took approximately 1 hour. I have a Bosch Axxis washing machine and all parts came exactly as ordered and within 2 days of order. I had to take off front and top panel and the door switch. The new wire and spring was part of the order and I had to pay for it. The old parts looked fine to me and I could have reused them but since I had the new ones, I replaced them anyhow. I wish I would have the option to buy the rubber gasket only.
Read more
More
Genuine Ge part
By: Ge
Part Number: WH1X2725
Secures your washer's drain hose to standpipe, maintaining proper air gap to prevent siphoning and backflow. Replace if clip is broken or missing.
Do-It-Yourself Stories from Customers like You
Burned out capacitor Mary V. • Ellenton , FL • June 06, 2016
My son fixed it
Read more
More