10650569992 Frig Parts

Ordered the parts, took door off the refrigerator. Removed all parts and replace with new parts. Took me about 15 minutes to complete. Read more

It was not looking good. I could not order the part I needed as it was part of the door - eve though it had screws att Hong it to the freezer door. At one web site it was a replacement of the whole freezer door!/? Luckily I ventured further and found this repair kit and video instructions. My order arrived in 3 days, and the install (thanks to the video) was easy. A whole lot better than buying a new freezer door - not! BTW - Whitlpool should not have made the tabs out of plastic, the metal... Read more

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

Had to replace the auger. The auger on my ice maker was made of plastic and had broken pieces off it. The new one is made of metal and seems to work much better. Was a fairly simple repair. However pay close attention when disassembling, I recommend using your cell phone and snap a pic of the different stages as I became a little confused when putting it back together. Ordered the part and it was here the next day. I'm very happy to have my ice coming down the chute again. By the way, I'm a 70... Read more

Undid a handful of screws, put the new panel in place and screwed them back in. Read more

• Won't start

Took the screws off the back plate at the bottom and watched the YouTube video on how to remove the cover plate for the starter and overload on the back of the compressor. Ended up snapping the old cover plate (brittle plastic) so I was glad the "kit" came with a new one. I used a small flat-head screwdriver and carefully pried off the starter and overload, then, with the new ones in hand, took the wires off the old ones and immediately put them on the new ones so I didn't lose track (there is... Read more

I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again. Read more

I replaced the Ice Dispenser Lever. Since the replacement part is only available in white and my fridge is bone, I replaced also the Water Dispenser Lever, so it looks much better. I followed the instructions in the video, which were very useful and very well done. My problem was that the refrigerator is a KitchenAid built-in, while the instructions were for a Whirlpool, so the removal of the faceplate was quite different from what was shown in the video and more difficult. Also there were some... Read more

Replaced with new one and followed the instruction from the video that is on the order Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

The water dispenser stopped working on my Sears Kenmore (Whirlpool) side-by-side refrigerator and after much research on the web I purchased the parts that commonly failed for this condition. I should have first taken the dispenser assembly apart but I didn't--it looked a little too intimidating to do twice. As it turns out, what actually broke was the plastic assembly that holds the water actuator switch in place so the dispenser lever could not strike it. I was able to secure it in place... Read more

I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The... Read more

Replaced the ice maker. The kit came with everything I needed to replace the ice maker. Parts that did not come with the kit were re-used from the old one. My Whirlpool refrig/freezer is an older model so the wiring harness that came with the kit was different from my existing. So instead of disconnecting the ice maker wiring harness from the freezer, I had to disconnect the harness at the ice maker. That was a b..... Anyway after about 20 minutes, finally unhooked the connector. I had... Read more

I ordered one from you. Read more

Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks. Read more