59212990 Parts

When starting my dryer the motor would power up and rotoe the drum and blower. Afetr about 20-30 seconds the igniter would come on then the gas valve would open and I would get heat for about 6 or 7 seconds then it would shut off. I know the burner is suppoed to cycle on and off but once the burner shut off it would not come bqack on unless I shut the dryer off and then back on. I checked for continuity on the thermistor, the thermal fuse and the high temp sensor. All three of them appeared to... Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

Replaced the following parts but did not fix the problem: -Thermister -Thermal fuse -Radiant sensor -Ignitor -Therm The problem was the Centrifugal switch. Took the switch apart and use fine grid sand paper to clean the contacts. Put it back and working. Read more

The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more

I ordered new door gasket, front and rear clamp for gasket and installed them. Read more

With all the bouncing around the shocks appeared to be done in but that was not the issue. The key was the balance ring. It had leaked all the fluid out causing all the beads to clump. This caused the drum to wobble wildly and not spin at speed. Getting to the ring to replace it is not a trivial task and took me several hours. Would have been much easier with help as the drum is quite heavy. The on-line video's are very handy and should be watched before attempting this job to save you a... Read more

Ordered a new leg from Appliance Parts & put it on. Read more

First I took off the spring loaded wire ring holding down the seal to the door with needle nose pliers. Pulled back the seal. Removed the 3 screws holding the part on the front of the washing machine. Slid the piece out. Took the protector guard off the off piece and unplug the wires. Put the wires into new part. Put the protector on the new part. Slid the part back into place. Screwed it back in. Put the seal back on. Put the wire spring loaded ring back around the seal. Total time 15 minutes... Read more

Appliance Pros made sure I had the correct part by verifying the model of my appliance. The part arrived on the scheduled day as promised I did the repair it myself. Read more

• Door latch failure
• Will not agitate

After watching the video it was strait forward. Just Pull the screws pop the lid swap the springs "grease them" and put it back together. I would suggest that you have a person help you mostly has a second pair of hands. The lid was over rear springs and it will save you some expletives to have the extra body. I had worn out springs and the load kept becoming unbalanced during spin cycles I just happened to coincide with the Lock mechanism failing. The motor drive for the lock stopped working.... Read more

I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more

Removed old lint filter cover. Inserted spring on one end of lint cover and installed cover. Read more

Removed top panel to reach the hose and sensor. Propped the washer back, reached up to remove bottom hose assembly. Replaced with new hose and new sensor. Put top panel back on. Parts place told me the part was backordered for months and repair would cost at least $80. Got it in three days and fixed it myself. Read more

• Will not stop filling with water

This error code indicated faulty water level and wash cycles were exhibiting either no water or too much water. Saw utube vid using this part for this type of problem and so far the repair is working well. Part arrived in 2 days, it was the right part and the machine is working the way its supposed to so I'm very happy. The worst scenario would have been to hire a repair guy to rip me off for a "Johnson Rod" I didn't need. Read more

Took out the original and put in the replacement. Read more

I got it in the mail, I opened it, I handed it to my wife....and she installed it. Easy-Peasy! (Being retired is a blast) Read more