Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dishwasher won't start or lights flash? The door switch signals the control board when closed. Easy DIY fix with video guide. Restore operation.
This was a difficult problem to diagnose. Because the machine would start the wash cycle then shut down after a few minutes of running, it appeared that the cause might be a bad thermostat or heating element, but all checked out ok. That led me to believe that the control panel may be the culprit but it also appeared to be working correctly when I ran the diagnostics program. A visual examination of the components found that the door switch electrical connections looked discolored, so I removed... Read more
Fix leaks around the dishwasher motor or poor spray pressure with this impeller and seal kit. DIY-friendly repair takes about 2 hours with basic tools.
My dishwasher quit cleaning dishes and lost all pressure. The food screen would keep clogging up and I would have to take it out and clean it by hand. After putting a new impeller in, the "gears" on the impeller connected with the screen blades, the old impeller the "gears" were stripped off. And the new impeller comes with new seals, after taking old one out I noticed it wasn't long before my old seals would have started leaking. Very simple repair if you watch the great video that... Read more
White retainer clip secures the kickplate at the bottom of your dishwasher. Replace if broken, cracked, missing, or lost to keep kickplate firmly attached.
Repair was easy. Just slotted the new parts in and they fit and worked fine, Read more
Replacement dishwasher panel that covers and protects internal components. Install to replace a dented, cracked, worn, or missing panel piece.
Ordered front panel and panel control. Also ordered name plate (did not need) front panel already has it. My husband and I had it switched out in approx 10 minutes. Took longer to gather proper tools than it did to do the repair. Looks awesome and original! Read more
Fix standing water in your dishwasher bottom with a check valve replacement. Prevents backflow and improves cleaning. DIY repair in 30-60 minutes.
The odor in the dishwasher was due to scum buildup in the walls, the racks, and in the lower part of the drain below the lower rotating arm. One of the valves in the vertical tube was stuck in the open position; since the valves cannot be replaced, the entire tube needed replacement. The check valve probably needed no replacement, but once I opened the bottom part, I decided to replace it anyway. I used this Youtube video to replace the tube, open and clean the drainage part of the washer: ... Read more
Replacement wheel assembly for dishwasher lower rack. Snaps onto rack to allow smooth gliding along tracks. Replace if cracked, broken, or missing.
Parts snapped into place very easily. Appliance Parts Pros have always delivered on the right part, timely delivery and videos to help. I wouldn't go anywhere else. Read more
The Upper Dishrack Rail is an OEM replacement part for Whirlpool dishwashers. It guides upper racks in and out for easy access to dishes.
Causes of faulty rails can include worn rollers, broken clips, or stress cracks in modules after repeated cycles.
Symptoms of a bad upper dishrack rail include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Ordered the parts and followed the instruction videos that Sears provide, Initially tried to order parts from Sears directly but the web-page kept complaining about my shipping address. Their loss- no wonder they're going out of business. Also, should note that the original assembly was plastic but the replacement was metal. Sure sign of a crappy cost-cutting decision. Overall, very happy with Appliance Parts Pros! Read more
The Filter Assembly is an OEM part for Whirlpool dishwashers. This component is responsible for trapping food particles and debris, preventing them from recirculating during the wash cycle and ensuring that dishes come out clean.
Causes of a bad filter assembly can include accumulated debris, regular wear from repeated use, or damage from harsh cleaning agents. A compromised filter can reduce the dishwasher’s cleaning performance and lead to buildup inside the machine.
Symptoms of a bad filter assembly include:
Replaced filter. It works great now, no more brown spots. Read more
Seals the dishwasher air vent to prevent water leaks during operation. Replace if you notice dripping under the vent or wet insulation behind the panel.
First tried replacing the seal around the door as that was the simple and most logical fix. Still leaked. Removed the front and upper panel to inspect. Found calcium deposit running down from under the Air Vent Assembly and wet behind the black stick-on insulation. Easy to trace the leak to the bottom of the door. => Ordered new Air Vent Assembly, gasket and Vent Deflector. Parts arrived. Took 5 minutes to remove upper panel. Removed the two wires from the Air Vent Assembly. Inserted a... Read more
Replacement door spring for dishwashers. Balances and supports the door during opening and closing. Replace if broken, fatigued, or door drops too fast.
Purchased door springs from Appliance Parts pros.com, installed them and door on our Dishwasher was back to normal, Had to pull out dishwasher from under cupboard to get to springs, as they were on the sides of the dishwasher. Read more
Fix blinking lights, won't start, or cycles not finishing? Replace your dishwasher's electronic control board. This 15-30 minute DIY repair can save $300.
We purchased the electronic control board (for 1/2 of what the technician wanted for the part), opened up the door to the dishwasher, took out the old board and put in the new one. It was a 15 minute repair and we saved almost $300 doing it ourselves! (Thanks to AppliancePartsPros.com and YouTube!) Read more
Side mounting bracket kit secures your dishwasher to adjacent cabinetry. Replace missing, damaged, or broken brackets for stable installation.
I haven't yet started to place the dishwasher in place is Read more
Replacement lower spray arm support bracket for dishwashers. Mounts underneath the wash arm enclosure to securely anchor the rotating spray arm. Needed when cracked or stripped.
We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more
Seals the water inlet connection to prevent leaks where water enters the dishwasher tub. Replace if you notice moisture damage or leaking at the valve inlet.
Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more
Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.
After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day. Read more
The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.
Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.
Symptoms of a bad spring tension hose clamp include:
Took off cover, installed new parts. Read more