Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.
New hose and clamp. Read more
Right-side oven rack support mounts to the interior wall to hold and guide oven racks at proper heights. Replace if cracked, broken, or missing.
This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.
I removed two sheet metal screws to remove the panel above the washing machine lid. That exposed four more phillips drive sheet metal screws, after removing those the dashboard control panel is held by two smaller black screws slightly recessed in the lower corners. This allowed the panel to be pulled down from the top, revealing the back of the switch. At this point I took a picture of the wiring connections with my cell phone to make sure I put them on the new switch in the same... Read more
The Power Cord is an OEM replacement part for Frigidaire refrigerators. As the lifeline connecting the appliance to a wall outlet, this cord safely delivers necessary voltage to operate refrigerator systems.
Potential causes for needing a new power cord include exposure to cuts, abrasions or rodent damage over time in the storage area. Repeated bending stress during installation or removal can also wear out plastic insulation faster.
Symptoms of a faulty power cord include:
This power cord also fits some Electrolux and Gibson refrigerators.
Fix a washer that won't start, stops mid-cycle, or leaves clothes wet. This electronic control board restores proper operation and reliable cycles.
Small spacer that fits on the idler assembly shaft to properly align the belt tensioner. Replace if worn, cracked, or missing to maintain proper spacing.
Reviewed items that might be the issue and ordered them. After installed noise was gone. Read more
Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.
Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more
Black graphic overlay that adheres to your range control panel. Replaces worn, bubbled, or damaged film to restore clear button labels and a clean look.
I read that the controller and probe controlled the oven temperature. Also read if replacing controller you should replace the overlay. So I ordered all three parts and installed myself with no problem. I took a photo with my phone prior to unplugging wires so I knew the right way to plug the wires into the new controller. Works like new. Only need a nut driver and screwdriver to repair. Job from star to finish approximately 30 minutes. Read more
Washer won't start, stops mid-cycle, or shows error codes? The control board manages all functions. Moderate DIY repair restores full operation.
Hi, it's me again. So I learned a valuable appliance repair lesson when trying to fix this washing machine: don't fix something until you figure out why it broke in the first place! The first speed control board died (fixed with my last story on year) and I assumed it was just a cheap part of something, but I was in fact proved wrong when, to my dismay, the new board died a week or so later. Being the self-appointed washing machine expert I became after the last repair, I got right into the... Read more
This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
Sits on the center hinge pin to maintain proper door spacing and smooth pivoting. Replace if worn, cracked, or missing to restore even door alignment.
Replaces a damaged, cracked, or missing bottom drawer on your range. Restores smooth slide action and a flush, finished look to the storage compartment.
Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:
Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.
I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more
Dryer overheating or taking too long to dry? This control thermostat regulates internal temperature by cycling the heater on and off. Easy replacement.
I replaced both thermostats, the seals and the heating element and the belt. It's an easy job to keep my dryer last longer. Read more
Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.
Removed the freezer shelves and back panel, evaporator coils were frozen with ice. Defrosted coil and removed defrost heater connectors, measured no continuity in the heater and ordered a replacement. Also discovered the aluminum retention strap was broken and the heater had slipped down in it's position, ordered and replacement strap. Re-installed new heater and strap per the video instructions, repair complete. Most difficult steps were drilling out the drain pan rivet and re-threading... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.