Bosch Sgs4352au/30 Parts

We replaced the black door seal gasket around the front of the dishwasher. The old black seal gasket had begun to deteriorate, every time it was touched black stuff would rub off onto hands and onto utensils in the upper basket. We wore some disposable gloves to remove the old seal to avoid getting the black stuff on our hands. Before entirely removing the old seal gasket we studied its placement to tell which way the new seal gasket should be placed. We didn’t want to place the seal gasket... Read more

I bought the door and bottom seal and was already to go. Appliance Pro got the parts to me in 2 days. I read an article that said if the spray arm holes are blocked that this could cause a wave in the dishwasher that could cause the water to fly up to the inlet used for drying and the water could run down between the front and inside door appearing to be a leak. I checked and my spray arms were indeed blocked. I pulled them out, cleaned them up, reinstalled, and low and behold that was appeared... Read more

I changed the control board (00498022) in the door of my Thermador dishwasher. Thermador, Bosch, and Siemens all use the same board for the indoor controls and display. This required a #15-star head driver to remove the screws. I used an impact wrench (set to a low torq setting) to speed things up. There are approximately 12 screws to remove. Two are long. The rest are short. Be careful to hold the door together as the last screws are removed. Everything comes apart easily and you do not... Read more

Removed water out of basin, down to the last inch.. Watched water rise slowly, and felt temperature, warm. This told me it was supply water. Ordered replacement part, two days just as mentioned, Removed as per video. Also choose to replace the waste line check valve, to affordable not too. Working great, except the wood floor not so happy with. One thing at a time. Thanks Read more

Bought new wheel and the are easy to replace. Found why the brok and did a quick fix so it wont happen again. As the wheels age one will pull off then they all get weak and the rack will come off the track, To prevent this. you can put a plastic tie so the wheels cant fall off in the first place, The disign holds them in place with pressure from the plastic but the plastic ages and gets weak. A tie would have to actually break before the wheel can fall off. Read more

Twist the old one out, insert tab, twist until other side snaps in. Easy as pie after watching the video! Read more

After having seen the video I installed the new lid and it worked. Read more

• Leaking

Ordered replacement drain hose, left hand panel of dishwasher removed (remove 2 screws in front left trim panel & friction fit clip at top back then slide up & off. This reveals the O-ring drain hose connection point. You need to remove the retainer block where the hose exits the appliance. Old hose pulls out and new hose pushes in. In the end a very easy installation. Most of the time spoent here is removal & reinstallation of dishwasher back into position - the actual hose swap takes 10 mins Read more

Checked out the AppliancePartsPros.com online parts/assembly diagrams for our Bosch dishwasher model and ordered the two sided set of new springs + connector ropes + connector-to-door ... plus a couple of other relatively inexpensive adjoining parts that might have become worn over time, just in case they were needed. The extra parts arrived in two days with standard shipping. Called about the "back ordered" primary set of parts (which had been listed as being "in stock" when I placed the... Read more

On my Bosch she55m15uc/64, the cycle would take 3-4 hours, with the machine stuck on "1 minute" for a long time. The interior was getting moldy and smelly, and the dishes had a white film. At first, I thought it was the heater relay on the control board, but I pulled that relay and it seemed to be working. I could get an ohmmeter on the heater element without taking the bottom off the dishwasher, and the resistance was infinite. Replacing the heater did the trick. On my unit there was a... Read more

After having seen the video I installed the new lid and it worked. Read more

• overflowing
• Will not fill with water

I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle. Read more

Easily installed the side mounts and put new trim around the opening. Read more

Used vids on youtube for steps on how to disassemble and install the pump; search "Bosch dishwasher circulation pump replacement". Also on AppliancePartsPro forums, a poster put up the Bosch "Dishwasher Service Training Manual" in .pdf. Search "Bosch dishwasher low pressure" on the forum. It's one of the post with the longest thread. Six pointers. 1. In another forum post, the poster noted that some hoses were brittle with age - and cracked when reinstalling. I had same issue (my washer is... Read more

This turned out to be a major effort, requiring me to disconnect the dishwasher, pull it from the cabinetry and partially disassemble the dishwasher to replace the door closer pulley Read more

Hearing a metal on metal noise and not actually circulate water cancelling cycle worked fine After some web research, I concluded it was highly likely to be the circulation pump, so I watched the video on AppliancePartPros.com and realized it was a lengthy repair (a lot of steps) but not technically difficult. I simply played and paused the video at each step and duplicated the steps. The biggest things to take note of: 1) take good pictures of the wiring to use when you re-connect. 2) Wear... Read more