Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer not heating or overheating clothes? A faulty cycling thermostat may be the cause. Regulates heat levels during the drying cycle. Easy DIY fix.
After 22 years my Kenmore (Whirlpool) dryer stopped getting hot. So I went ahead and reviewed the videos and figured I could repair it myself. It should be noted that the only part that failed the Ohm test was the thermal fuse. However, I figured that since I have it apart, I might as well go ahead and replace the heating element and the cycling thermostat. Here is a rundown of what I did and how long it took: • Taking the back off and vacuum <1 minute • Finding the components (from the... Read more
Dryer won't heat or flame shuts off after 15 seconds? Gas valve coils control gas flow to the burner. Takes about 30 minutes to replace both coils.
I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more
Replacement drum support roller for dryers. Installs on the drum assembly to allow smooth rotation. Replace when cracked, worn, or making noise.
I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more
This dryer drum belt connects the motor to the drum for proper rotation. Replace when the drum won't spin or makes squealing sounds. Verify fit by model number.
I watched your initial video which gave me some insight into the repair. I removed power from the dryer and positioned it for maintenance. Since my dryer was a Maytag, I needed to remove to two front bottom Phillips screws from the front panel of the dryer prior to pulling the panel and door assy. from the unit. The top of the dryer now needs to be removed. Two screws, one on each side holds the top of the dryer in place accessible from within and under the top of the dryer. Once those two... Read more
Dryer making rumbling noise or drying slowly? A worn blower wheel with a rounded center causes wobbling and poor airflow. Moderate DIY repair.
In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more
Dryer won't heat or flame goes out after ignition? The flame sensor monitors burner flame presence. Common DIY fix with multimeter testing required.
I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more
Supports drum rotation and reduces friction. Replace when dryer squeals, rumbles, or drum sticks. Includes mounting hardware. Verify fit by model number.
Replace worn pump and drive belts to restore agitation and draining. These belts act as the washer's clutch. Verify fit by your model number.
The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more
Retaining clip secures mixer components in place. Replace if cracked, rusted, or missing to restore proper assembly and stability of internal parts.
The blower wheel had been previously “repaired,” but the repairman did not install a retaining clip or clamp, so the new part was destroyed in about a year and a half, as the motor shaft rounded all the square edges in the plastic hub. The old blower wheel came off easily and the new part was a perfect fit. The center clamp that comes with the blower wheel kit would probably hold it in place by itself, but I also purchased and installed the retaining clip (#35) as well, because the end of the... Read more
Gas dryer not heating? A faulty igniter is the most common cause. This part ignites the gas burner to heat your dryer. DIY-friendly, installs in 30 minutes.
I checked repair videos on line. Put in my brand and model. You tube had a video how to dis assemble my model. Video made it really easy, I would never have figured it out. Now checked videos from Appliance Parts Pros to troubleshoot the fix. Checked all thermostats and fuses with ohm meter they checked out perfect. Finally checked the igniter found out I did not have resistance. I was also concerned I may need new coils (solenoids). In visiting with customer service he explained... Read more
Idler pulley wheel installs near the motor to guide and tension the drum belt. Replace if cracked, worn, or bearing has failed after years of use.
Washer won't start or stops mid-cycle when door opens? The door switch detects door position for safe operation. DIY repair in 10-20 minutes with video.
The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more
Dryer won't start or runs with door open? This door switch kit restores safety shutdown function. Simple clip-in repair takes 15-30 minutes. Video included.
The timer knob simply pulls off the shaft with a solid, steady pull. Cleaned the timer cavity of lint/dust buildup. Aligned the keying flat of the shaft and knob and pushed the new knob on with careful, steady pressure until it was obviously seated. No tools required other than a vacuum. The door switch would sometimes not shut the dryer off when the door was opened. New switch came with new fast-on connectors. Replacement required opening the top cover of the dryer and hinging it up. This... Read more
Traps lint and debris during drying cycles to prevent exhaust clogs and maintain efficiency. Replace when torn, damaged, or not catching lint properly.
This was a Maytag DE312 actually a Whirlpool labeled as Maytag) and is 27 years old. Replaced motor, drive belt and drum rollers. One tricky part was the motor because the new motor comes with integral starter and it was necessary to cut off existing female spade connectors on some wires and crimp on new connectors. Instructions were adequate but need to be carefully followed and a decent electrical stripping and crimping tool must be at hand. I bought a new motor drive pulley because another... Read more
Supports the inner tub for smooth spinning during wash cycles. Replace when you hear grinding noise or see water leaking from bottom center of tub.
I ordered the tub seal and stem seal kits along with the much needed spanner wrench. After viewing the video online several times and taking notes along the way I was ready to tackle the repair. After taking everything apart, I cleaned all areas thoroughly then addressed the rusty areas and mineral deposits found in the tub. Soaking the tub in vinegar and baking soda overnight helped loosen the built up deposits enough so I could carefully scrape them off with a spatula. This was very time... Read more
Fiber washer that maintains idler pulley alignment and belt tension in your dryer. Replace if squeaking, grinding, or pulley wobbles occur.
I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more