Maytag Lde9206ace Parts

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

• Will not tumble

I watched your initial video which gave me some insight into the repair. I removed power from the dryer and positioned it for maintenance. Since my dryer was a Maytag, I needed to remove to two front bottom Phillips screws from the front panel of the dryer prior to pulling the panel and door assy. from the unit. The top of the dryer now needs to be removed. Two screws, one on each side holds the top of the dryer in place accessible from within and under the top of the dryer. Once those two... Read more

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

I replaced the belt, belt tension pulley, both dryer drum roller axles and both drum support rollers. Although I bought 2 tumbler bearing kits, because those still look good I am saving them for when they go bad. The videos were fantastic! I also took pictures as I went of wiring so there would be no question where things went when reassembling. It should be noted some models have extra terminals near the sensor terminals... just be aware and look closely/take pics as you are taking things... Read more

• Will not tumble
• Noisy
• No heat or not enough heat
• Takes too long to dry

The blower wheel had been previously “repaired,” but the repairman did not install a retaining clip or clamp, so the new part was destroyed in about a year and a half, as the motor shaft rounded all the square edges in the plastic hub. The old blower wheel came off easily and the new part was a perfect fit. The center clamp that comes with the blower wheel kit would probably hold it in place by itself, but I also purchased and installed the retaining clip (#35) as well, because the end of the... Read more

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

• Too hot
• No heat or not enough heat
• Takes too long to dry

Replaced the thermostat and fuse it could have been either of them that was causing the issue - and now it works like a charm. Read more

• Doesn't shut off
• Won't start
• Will not tumble

The timer knob simply pulls off the shaft with a solid, steady pull. Cleaned the timer cavity of lint/dust buildup. Aligned the keying flat of the shaft and knob and pushed the new knob on with careful, steady pressure until it was obviously seated. No tools required other than a vacuum. The door switch would sometimes not shut the dryer off when the door was opened. New switch came with new fast-on connectors. Replacement required opening the top cover of the dryer and hinging it up. This... Read more

I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more

• Will not tumble

This was a Maytag DE312 actually a Whirlpool labeled as Maytag) and is 27 years old. Replaced motor, drive belt and drum rollers. One tricky part was the motor because the new motor comes with integral starter and it was necessary to cut off existing female spade connectors on some wires and crimp on new connectors. Instructions were adequate but need to be carefully followed and a decent electrical stripping and crimping tool must be at hand. I bought a new motor drive pulley because another... Read more

I research it online and found that my timer knob skirt was cracked, watched the video online to see how to fix it, ordered the part………it came within 2.5 days. I followed the instruction on the video and was able to fix it myself. I love that I am able to fix things like this myself, I will use this site again for my next repair needs. Thank you Read more

Started my Maytag dryer (model LDE8200ACW) with a large load early Saturday morning and immediately heard a noticeable thumping noise as the drum turned. Opened the door and checked to make sure some of the laundry hadn’t wadded up and was causing the thumping. Restarted it but the thumping was still present. Did a google search for obvious possible causes for the symptoms but the only suggestion that made sense was to check and make sure the dryer wasn’t rocking on its feet. Checked and found... Read more

I replaced the motor and all other moving components along with the felt drum seals.drum glides and drive belt. The wiring instruction is where i had the most problems. Because my wiring had only 4 wires in the harness not 5, and one was a different color then the instructions call out, I believe was because it might have been and older model. the instruction called for a gray wire but mine was white with a blue piggy back wire attached. but after finding a few videos on line i figured that the... Read more

• Noisy

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

• No heat or not enough heat
• Takes too long to dry
• Noisy

Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more

• Will not tumble

First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more