Dg9001068h Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Will not tumble
• Noisy

I've had this dryer apart a few times over the years, always got my parts here. Squeaks and igniter if memory serves. I ordered the two drum rollers that have a bearing in the center..they sit on metal shafts and freeroll. I ordered two..only one was bad but I needed the dryer up in one day, no time to disassemble and decide what to order then wait for parts. Tip: if you order the rollers, there are little washers (nylon?) between the roller and the c clips..don't lose them..they are hard to... Read more

• Too hot
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more

• Noisy

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

Instructions were on line. It was a quick easy fix. Read more

• Will not agitate
• Pumps but will not spin
• Will not tumble
• Noisy

Upon removal of the lower inspection panel on the front of the machine, my 20 year old son thought the motor was bad by the smell. But he did discover what turned out to be the belt tensioner pulley laying inside the machine. After he pronounced it dead, without a thought to the idler pulley, I looked at the machine and determined the lack of movement was due to the idler pulley having "fallen" off the shaft by looking at the illustrated parts break down provided on this website. Ordered the... Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

• Will not tumble
• Will not agitate
• Pumps but will not spin

Upon removal of the lower inspection panel on the front of the machine, my 20 year old son thought the motor was bad by the smell. But he did discover what turned out to be the belt tensioner pulley laying inside the machine. After he pronounced it dead, without a thought to the idler pulley, I looked at the machine and determined the lack of movement was due to the idler pulley having "fallen" off the shaft by looking at the illustrated parts break down provided on this website. Ordered the... Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more

• Too hot

I removed the front panel and observed the heating element while running the dryer. It was cycling off every minute or so and staying off for several minutes. Even though it was likely the high temp cycling thermostat I replaced both the 14, and 15 cycling thermostats which I think are the original factory units. That makes them nearly 35 years old. Problem fixed. Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more

I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more

I removed the burners, which were rusted and needed some tapping.They were pretty stubborn to remove from the insert. I removed the spark igniters, which were rusted where they screwed into the burner and then removed the venturi tubes.. Once this was done, I installed the new igniters to the underside of the new burner. I then installed the burners, which only took simple placement and a quarter turn to lock them in. I then hooked up the igniter wire to the new spark igniters. The repair... Read more

• Noisy

Took it apart. Replaced various general maintenance parts, rollers, seals, clean out all the lint and replaced motor and put a new blower on it. Read more

• Shakes and moves

New leveler pads Read more