Fffw5000qw Frigidaire Front Load Washer Parts

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

I called Appliance Parts Pros and they sent me my frame for my washing machine. This company needs 10 stars. They were excellent and very polite and very knowledgeable on what needed to be ordered. I would never purchase another Frigidaire item as the quality is not there. I would recommend looking at this site for any parts needed for anything. It was a pleasure talking to them and the item shipped very fast and was here in 3 days. Thank you Appliance Parts Pros you are the best. Read more

• Leaking

Y'all! This video made fixing my washer easy peasy. The service repair man wanted $352! I paid less than $200 for the parts. I also called around and appliance parts pros was by far the cheapest option. The shipping was unbelievably fast. (Faster than my amazon prime!) Read more

Removed old bellow following procedures found on relevant Youtube videos. Reinstalling however was more of a challenge. Getting the rear seal of the new bellow on the washer housing was not as easy as the videos indicated. The key to that process is being sure the seal is well lubricated which is not quite apparent from the videos but is essential success. Once the rear seal is installed, reapplying the rear spring was accomplished with the spring clamps as per the videos. Be sure to... Read more

Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank Read more

Got online and searched for part by washer model number. Found AppliancePartsPro.com. They listed diagram of part. I ordered it online and received it next day with no extra charge for fast delivery. My husband attached cosmetic drawer cover to detergent drawer part we ordered in a few minutes. It fits and is working! Speedy service was appreciated. Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

Watched the video a few times for door boot seal replacement. It was a lot of help! The spring is the hardest to replace and I did enlist the help of my wife. Everything went back on great. If you have to replace the front panel (with the buttons) be mindful that the buttons are spring loaded and will come out. I did not lose any and it went back together just fine. A little touch up paint on the washer and it all looks brand new and works great. And the parts came in quicker than... Read more

My teenaged son took the old washer door off and apart. He replaced our glass from our washer onto the new doors and attached it to the hinge. These doors are compatible with Kenmore washer even though it says Frigidaire. Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

Since I hadn't found the Tech Sheet for the washer (which there should be one inside the top cover) I simply thought I'd buy the drive motor (and a new belt, a.k.a "cheap insurance"). Installed the motor once I'd received it from AppliancePartsPros, the washer worked a couple of cycles then gave me the same "SrV CLL" message. I didn't know how to access the error codes on this model but found the info in the Tech Sheet, so I checked it and got an E53 code. Since I'd replaced the motor... Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

I tore it apart using. YouTube videos to guide me and found the shocks were loose and floppy. I found the shocks in stock here and had them in my hand 2 days later for only $10 shipping! It runs great now! Read more

Bad drain pump impeller--installed new pump and filter you guys rock! right parts ,right price, on time! Read more

It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more