Fwtb59rgso Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

• Shakes and moves
• Noisy

I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more

• Will not drain

Replace the drain pump after watching a video demonstrating the process. The washing machine had run properly and emptied, so I was surprised how much water remained in the pipe after disconnecting the old pump. Plan on having 2-3 large towels underneath before removing it. The most difficult part (and most irritating) was replacing the intake and outtake hoses with the existing spring clamps. The drain hose into the pump took almost twenty minutes to attach properly. If the hardware store was... Read more

• Spins slowly

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

• Shakes and moves

With more difficulty and frustration than expected but it works fine now. Things learned: 1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture. 2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too. 3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the... Read more

Replaced springs and shocks. Read more

It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more

I replaced the door boot with a new one from AppliancePartsPros.com. The most difficult part was starting at the back end of the new boot onto the stationary rim, just in front of the tub. And then anchoring it in place with the existing spring from the previous boot. To start the boot I had to hook the top edge of the boot, where the arrow tab is, onto the rectangular projection on the tub rim and then roll the rubber boot edge down around the tub rim and hope the rim was going into the... Read more

I changed the pump and also discovered the coin trap was wearing thin because it was rubbing against the sheet metal. So I replaced that as well. It took about 15 minutes to remove the coin trap and pump and about 20 minutes to install. The shipping was amazingly fast. I received the parts the next morning. I'm talking I ordered the parts before noon, chose the "fast shipping" option and received parts the next morning around 8:30 AM. Read more

Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more

I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more

New hose and clamp. Read more

Three new vanes. Installation was easy, removed one stainless screw on each vane, slid the broken vanes toward the front of the machine, compressed the old vane slightly and came right out. They have to be slid about 1 to 2 inches forward for removal. This was an easy fix. Read more