Gmc275pr001 Parts

• Oven not heating evenly
• Little to no heat when baking
• Element will not heat

I began by turning off the breaker. I then removed the screws securing the bake element. I immediately noticed only one side was wired and the other side was burned off. The wire for the burned off section had fallen through the hole in the back of the oven. I tried fishing it out to no avail. I removed two side trim screws, the side trim pieces, and two screws holding the built-in oven into the wall. I was able to slide the oven out and onto a square stool that was the correct height. I... Read more

• Oven is too hot
• Oven not heating evenly
• Little to no heat when baking
• Won't start

I have a Whirlpool RBS245PDQ12 wall mount oven. Gathering information from AppliancePartsPros.com resulted in two possibilities: The Thermal Switch or the Control Panel. Talking with Appliance Parts Pros led to testing the Oven Temperature Sensor. It's supposed to test at 1080 Ohms at 70 degrees Fahrenheit. Mine tested at 960 Ohms so I knew it was bad... I found the service manual on the top of the Oven on the left behind the control panel. It has values for testing (Ohms of resistance)... Read more

• Little to no heat when broiling
• Element will not heat

Found a real cool Youtube video by AppliancePartsPro.com. I watched it and learned how easy it was to unhook and replace the part with proper care and precautions. It even included tips on critical steps so the wires won't slip back inside the hole and save you from hours of possible mistake. Then I ordered the part. It came the day after, then I replaced the part, meaning, I DID THE WORK! (My wife was so impressed- lol) Easy as pie... but we made and had a much nicer roast the day after.... Read more

The most difficult part was figuring out how to take the door off as the manual instructions were not clear. Thank you, YouTube for your help. This door doesn't have the more modern release latches. You open the door all the way and stick Allen wrenches into the holes that appear by the joint of the latch. When you close the door to 3/4 or 7/8 closed, the latches are released from the unit and by holding the sides of the door, you pull it out. The whole replacement would take around an hour,... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

This was a very easy replacement of the broken glass turntable. What stood out most for me on this was the great experience I had with ApplicancePartsPros.com. I rarely, if ever, write reviews but this experience deserves notice. I found a couple other sites that had a slightly lower price, but AppliancePartsPros.com made it easier for me to verify that I was ordering the right part. On checkout, I selected standard shipping but the part arrived the next day. It was very well packaged (glass... Read more

Removed the Microwave from the wall, then had to almost completely disassemble the sheet metal surrounding the microwave unit itself. Lots of screws and wires to work around. Takes 2 people to remove the microwave and set it on a stand outside of the wall unit. Once you get to the light bulb, the replacement is easy, just very challenging to get to the light bulb. Read more

Touch up paint Read more

Replaced It With New One Read more

I'm a 56 year old divorced woman. I started doing these kinds of repairs to save some money and honestly, to see if I could. So yes, if I can do it, it's not that tough to do. My microwave is built in above the stove - getting it down and back up was the hardest part of the job. An extra pair of strong hands really helps-for anybody, not just a 56 year old woman. The actual repair was pretty easy. Most likely problem was pretty obvious after a little research. Easy to take off cover, get... Read more

Ordered the new fan (blower) from AppliancePartsPros. It arrived 3 days later. Pulled the wall oven out of the wall, removed the sheet metal back and removed the noisy fan. Installed the new fan, reinstalled the sheet metal back, shoved it back into it's place, turned the power back on and viola!, much quieter. Read more

We ordered the part and one extra screw(which we didn't end up using). If possible take door off your oven for easy access and have lighting source to see well. Taking part out was easy. Putting back in was more difficult because you have to match up two layers of parts in our oven. The broiler coil and the broiler shield above it. We used small craft clothes pins to keep wires from going behind the built in oven. We used a small diameter screw driver to match up holes before putting... Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

• No heat

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

We replaced the middle glass and spring by taking the door apart with no problems. Read more

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more