Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Left-side oven door hinge that supports and controls door movement. Replace if hinge is cracked, broken, or door won't close flush, allowing heat to escape.
The replacement hinge unit arrived in just two days. The JennAire (Maytag) oven door is fairly typical in that it easily lifts off of the hinge bars. Once the door is off then removing two screws is all that's required to remove the hinge unit from the oven. The new hinge slides up into place and while you hold it up inside of its location putting the old screws back in is very easy. After sliding the door back down onto the hinge bars the oven is as good as new Read more
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Broil setting not heating? This upper oven element delivers direct radiant heat for broiling. Easy DIY fix with a screwdriver in under 30 minutes.
Very easy fix. Remove oven door by just opening it slightly and pulling up. (an easy way to clean it too). Then, with a phillips screw driver, remove two screws holding the damaged element in place. Slowly pull the element toward the front a couple inched to expose the wires. Disconnect the wires (no tools needed), remove the old element and replace it with the new. Reverse the past few steps and re-attach the wires and screw. Simple as that. I also chose to replace the Broiler Element as a... Read more
Fastening screw for securing components inside appliances. Replaces lost, stripped, or damaged screws during repairs or part installations.
Bought and installed new hinges. Repair took about an hour but I also cleaned all the glass inside and out on both oven doors. I had ordered extra screws as I read the old ones that hold the hinges were hard to get in as they were self taping but the screw labeled 5 next to the hinge were not the right ones. All old screws worked fine. You just need to put a little power to them to get them started. Easy repair. Read more
Indicator light that illuminates when functions are active on your range control panel. Replace if stuck on, dim, or fails to light. Verify fit by model number.
I ordered the replacement part and undid two screws on the front of the cooktop then used a nut driver to undo the clamps holding the burner in.I took a picture of the wiring then used needle nose pliers to gently pull the connectors off the terminals. reinstalling you just line up the new burner with the old one and screw the clamps back on. there are no predrilled holes the screws just bite into the insulation. Read more
If your broil function won't heat or brown food properly, a failed broil element is the likely cause. This upper heating element restores direct radiant heat.
This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.
I completely disassembled the entire unit sandblasted repainted with epoxy paint and reassembled. bought a few new parts and its like new again this unit is no longer available and its built into my boat. Read more
This is a high-heat ceramic light receptacle used in select appliances. It provides a safe, insulated socket for the appliance light bulb so you can reliably see inside during use or service.
Took apart the burner unit and replaced burned spade. Did not need the receptacle, so returned it, but did have to order the contact and lead wire that burned out in it, and what really caused the whole problem. That will be covered in another repair note for that part. Read more
To order indicator light use WP903115.
Replaced coils on gas valve; while at it replaced door screws which were starting to wear from assorted repairs over the years. Read more
Fixes burner that won't heat or indicator light stuck on. This infinite switch controls surface burner power and heat settings. Moderate DIY repair.
Replaced switch Read more
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more
Anti-tip bracket bolts to the floor behind your range to prevent tipping. Replace if missing, bent, or damaged during moving or installation.
Part arrived quickly and was an easy install1 Read more
This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:
I replaced the downdraft fan and fan motor of my 25 year old JennAire C301 cooktop. The issue was getting the fan/motor assembly out in such a tight place. I had to first remove the fan cover, cut the wires, then the assembly came out. Putting back wasn't as tough although getting the cover back on (over the motor) was a bit of a strain. Wired it back, turned it on, and was thrilled. Now I'll replace the knobs and burners and we're back in business. Read more
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
It was very easy to fix after watching your video.. Read more
Fix unresponsive buttons, dim displays, or total control failure. This range electronic control board restores all functions. Moderate DIY repair.
I replaced computer board on stove. Read more
Replacement oven door hinge for ranges. Supports and guides the door through opening and closing. Install when original hinge is broken, worn, or fatigued.
The new hinges from Appliance Parts Pros were a perfect replacement and easy to install. Thanks. Read more