Kuds30ixssr Parts

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

Color: Stainless

This electronic control board is the dishwasher's main circuit board. It directs wash, drain, and dry functions and coordinates the user interface. Replacing a failed board restores responsive controls and reliable, complete cycles.

• Times and sequences wash, drain, and dry operations
• Distributes power to the circulation pump, drain pump, inlet valve, and heating circuit
• Monitors sensors and door switch; communicates with the display/indicator lights
• Common symptoms: won't start, unresponsive controls, cycles that stall or never advance, blinking lights or error codes

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use ESD protection and handle the board by its edges
• Label/photograph connectors; transfer any mounting brackets or jumpers from the original board
• Some models require configuration/programming after install—follow the tech sheet stored inside the unit

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

Color: Black

This mount secures the dishwasher's upper spray arm to its water feed, keeping the arm aligned and free to rotate so the upper rack receives consistent spray coverage and dependable cleaning.

• Supports and centers the upper spray arm at the correct connection point
• Helps maintain a solid connection to the feed tube/manifold for proper water delivery
• Wear, cracks, or looseness may lead to poor cleaning on the upper rack, arm wobble, or noise
• Replacing a damaged mount can help restore smooth spray arm rotation and wash performance

• Disconnect power and turn off water supply before servicing
• Pull out the upper rack; remove the upper spray arm from its mount
• Release the old mount's locking tabs or fasteners and remove it from the feed tube/tub
• Install the new mount fully, reattach the spray arm, and verify it spins freely before testing

This vent door bezel is the trim piece that frames the vent opening on the dishwasher door. It restores a clean, finished look and helps keep the vent assembly properly seated if the original bezel is cracked, loose, or missing.

• Mounts on the exterior of the door around the vent outlet
• Provides a finished edge and helps retain the vent assembly/gasket
• Replaces damaged or missing trim that won't stay attached
• Common symptoms: broken tabs, loose or rattling vent trim, visible gap or cosmetic damage around the vent

• Disconnect power to the appliance; turn off water supply if needed
• Open the door and remove fasteners to access the vent area behind the panel
• Release the old bezel (tabs/screws), align the new bezel, and secure flush to the panel
• Do not overtighten fasteners; avoid vibration or leaks

This fold-down tine pivot for the lower dishrack acts as the hinge and latch for the adjustable tine row. Replacing a worn pivot restores stable loading and allows the tines to flip up or down as designed. What it does:

• Supports and pivots the fold-down tine row on the lower dishrack
• Holds tines in either position to accommodate different dish loads
• Common symptoms: tines won't stay upright, adjustable row detaches, cracked or missing pivot
• Helps prevent dishes from tipping during wash cycles

• Disconnect power and water supply to the dishwasher for safety; remove the lower rack
• Release the old pivot's locking tabs and slide it off the rack/tine row
• Align the new pivot with the rack wires and tine row; snap securely into place
• The tine row pivots smoothly and holds in both positions

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

12 Ft in length

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks