Lat2600aee Parts

I replaced the entire agitator (my appliance agitator could only be replaced in one part not the upper part only). It was super easy but one thing....the video on the website was not helpful because my maytag washer is older and does NOT have a screw down inside the agitator but has one 1/4 inch hex nut on the side down by the base. Good for me though because all I had to do was unscrew the nut, put the new agitator on, tighten the new nut and DONE!! Read more

• Lid or door won't close

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Replaced flow meter and control valve Read more

• Noisy

Replaced them. Read more

Replaced the tube and the clamp Read more

Ordered a replacement valve and installed it. The part from AppliancePartsPro was an exact replacement for the original part. Replaced the hot and cold hoses at the same time to insure no leaks. Cold water settings now work properly again. Read more

• Shakes and moves

Took off the old parts and replaced with the new parts Read more

• Shakes and moves

New leveler pads Read more

I bought the $6.00 plastic clip that holds the agitator In place while washing and the $10.50 spanner wrench that takes the 2 top nuts off to get to the agitator stem the other tools necessary for the job which are just a couple of things I already had then watched the video on line of how to do the job and then did it the whole thing took about 2 hours plus I took my time and gave both tubs a very good cleaning. I paid a guy $400.00 9 months earlier to do the same job wish I hadn't, should... Read more

Ordered the new part from you guys. Installed it within 5 minutes. Works like new again. Read more

Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more

Replaced both, the water level switch and the water level hose. Watched the how to video first on your site and made the repair easy. Read more

Took off the back of the top pushed the switch forward and lifted it out after I unplugged it. Put the new switch in the opposite of how I took it out, plugged in the wires put the back on and finished my laundry. Read more

Removed the old tub cover/gasket by removing the front panel and top lid. Then, unclipped the tub cover. Read more

We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more

Removed lid sanded down all rust spots, taped over the printed instructions on the inside of the lid, washed with alcohol and spray painted with appliance white epoxy paint. Replaced the plastic hinge-balls and one of the lid support/bumper grommet. It was actually easier to install the lid than removing it; used a small amount of grease to hold both balls in place, by holding the lid vertical and placing the left side to the inserted ball and then pushing the right side down. The lid slides... Read more