Maytag Lat9457bae Timer Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001304
The Water Injector is an OEM part for Whirlpool washing machines. This component is responsible for distributing water into the washing machine during the wash cycle, ensuring that clothes are thoroughly saturated and cleaned. It connects to the water supply and directs water into the tub at the appropriate times.
Common causes of a bad water injector include blockages from mineral deposits, wear and tear from frequent use, or damage due to high water pressure. Over time, the injector's effectiveness can diminish, impacting the washing machine's performance.
Symptoms of a bad water injector include:
- Insufficient water entering the washing machine
- Longer fill times or failure to fill at all
- Poor cleaning performance
- Leaks or drips around the injector area
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Water squirted out the back of the machine when i tried to fill the tub Walter W. • Saint Paul , MN • June 30, 2014
Removed the front panel and removed the screw from the console which revealed a broken plastic tab on the right side of the old injector. Replaced the old injector with the new one and that took care of the problem.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001007
Seals the tub cover to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the tub. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Leaking water from washing tub E M. • Danville , KY • May 22, 2016
Replaced mounting stem and tub bearings
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 207843
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
Do-It-Yourself Stories from Customers like You
Bearings were worn out makeing a lot of noise Lawrence L. • Largo , FL • August 08, 2015
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP89503
Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.
Do-It-Yourself Stories from Customers like You
Low water flow and fabric softener would dispense immediately when cycle started Bob G. • Sylacauga , AL • January 19, 2019
Replaced flow meter and control valve
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP211726
Small plastic ball component that snaps into washer lid hinge mechanism. Replace when missing, cracked, or broken to restore smooth lid opening and closing.
Do-It-Yourself Stories from Customers like You
Sometimes the washer wouldn't start the wash cycle when the fill cycle was done it would just sit until the lid was picked up or bumped Eugene N. • Roswell , NM • August 28, 2016
The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001650
Secures components with constant tension to prevent looseness and vibration. Replace if broken, fatigued, or missing. Verify fit with your model number.
Do-It-Yourself Stories from Customers like You
Drum guides had worn out Robert S. • North Apollo , PA • October 08, 2014
Replaced them.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP96160
This is a small mesh filter screen that fits inside the water inlet valve to catch sediment and debris from your household water supply before it enters the washer. It prevents mineral buildup and particles from clogging or damaging the valve internals. Replace this screen if your washer is filling slowly, not filling at all, or if the screen is visibly clogged, torn, or deteriorated.
Do-It-Yourself Stories from Customers like You
Washing machine was having trouble delivering enough water on rinse cycle Cynthia S. • Libertyville , IL • August 15, 2014
Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001320
Bleach leaking onto the floor or not dispensing? A cracked or hardened bleach tube is the likely cause. Simple 5-minute fix with basic tools.
Do-It-Yourself Stories from Customers like You
Leaking bleach tube Mike C. • Willow Grove , PA • May 21, 2017
Replaced the tube and the clamp
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP210684
The Leveling Leg Pad is an OEM replacement part for Whirlpool washing machines. This small but essential component fits beneath the leveling legs, providing stability and preventing the appliance from moving or vibrating excessively during operation. It also protects flooring surfaces from potential scratches or damage.
Symptoms of a bad Leveling Leg Pad include:
- Increased vibration or noise during the wash or spin cycle
- The washing machine wobbling or becoming unsteady
- Visible wear, cracks, or damage to the pad
Causes of a failing Leveling Leg Pad can include wear and tear from prolonged use, exposure to moisture, or excessive weight causing deformation. Replacing worn pads helps maintain the appliance's balance and efficiency.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
For the leveling leg order 22003428.
Do-It-Yourself Stories from Customers like You
Washer "bucking" while in spin cycle Luis P. • Loveland , CO • June 27, 2017
New leveler pads
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 22003428
Leg, adjustable (w/nut)
Do-It-Yourself Stories from Customers like You
Needed new support adjustable legs for my maytag washer Rodger M. • San Clemente , CA • November 17, 2014
Took off the old parts and replaced with the new parts
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22002340
Secures the agitator to the drive shaft in top-load washers. Replace this collar if it's cracked, worn, or missing to restore proper agitator alignment.
Do-It-Yourself Stories from Customers like You
Agitator kept floating up when washing and would not wash or agitate Todd W. • Alhambra , IL • December 13, 2015
I bought the $6.00 plastic clip that holds the agitator In place while washing and the $10.50 spanner wrench that takes the 2 top nuts off to get to the agitator stem the other tools necessary for the job which are just a couple of things I already had then watched the video on line of how to do the job and then did it the whole thing took about 2 hours plus I took my time and gave both tubs a very good cleaning. I paid a guy $400.00 9 months earlier to do the same job wish I hadn't, should...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003363
Fix a washer that won't advance through cycles, skips spin, or runs continuously. Timer replacement typically takes 15-20 minutes with basic tools.
Do-It-Yourself Stories from Customers like You
Timer switch on my washing machine Justin M. • Mandan , ND • February 03, 2017
Ordered the new part from you guys. Installed it within 5 minutes. Works like new again.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22003410
Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.
Do-It-Yourself Stories from Customers like You
General overhaul of a 14 year old machine Todd F. • Wellsburg , WV • January 20, 2016
Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22002417
This rubber seal creates a tight barrier between mating components to keep water contained and stop drips. Replacing a flattened or cracked seal helps prevent leaks and protects nearby parts from moisture-related damage. What it does:
- Forms a watertight gasket between two parts in the assembly
- Helps prevent drips or seepage at the connection point
- Restores proper compression when the original seal hardens or deforms
- Common signs of failure: leaks, dampness, or visible cracking/flattening of the old seal
What's included:
Install notes:
- Disconnect power; for water-bearing assemblies, shut off the water supply
- Access the seal location per your service information and note orientation/depth before removal
- Clean mating surfaces; lightly moisten the new seal with water or mild soap to ease installation
- Ensure the seal is fully seated, reassemble, and test for leaks
Do-It-Yourself Stories from Customers like You
Collar on transmission agitator shaft became loose and allowed the attached agitator to float upward and fill the transmission with wash water Eddie H. • Sandia Park , NM • February 29, 2016
Removed agitator, inner washer barrel, and agitator shaft then drained all the water and emulsified oil out of the transmission. Filled the transmission with new oil and then replaced the worn agitator shaft, shaft collar, shaft o-ring and stem sealing system.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001776
Fix washer overfilling or not filling properly with a new water level pressure switch. Controls fill shutoff and cycle transitions. DIY repair.
Do-It-Yourself Stories from Customers like You
Water level switch not working. Steve S. • Anderson , IN • January 22, 2018
Replaced both, the water level switch and the water level hose. Watched the how to video first on your site and made the repair easy.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21001905
One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.
Do-It-Yourself Stories from Customers like You
The upper agitator kept floating off Brian T. • Pine Grove Mills , PA • October 02, 2018
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do.
Read more
More