Maytag Lsg7806aae Parts

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

• Will not fill with water
• Will not agitate

First I needed to replaced the timer. However that timer is no longer available. So I was not able to buy that part. A friend encouraged me to cross reference the part number. I did and I found another timer that claimed it would work on my machine. It looked very similar. I got the timer from you guys and put it in. The water valves worked right away but the motor did not. I researched more troubleshooting ideas and discovered I had a bad lid check switch. I got a new one of those from you... Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more

• Won't start
• No heat or not enough heat

Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more

I decided to order the siphon break kit (siphon break, washer and clamp included), a new hose, and clamp (for the bottom hose connection) as the hose was original and well over 15 years old. I probably could have used the old clamp, but decided to get a new one in case there were problems with the old during removal. The video provided by A.P.P was helpful in giving confidence this was a task that could be done by myself. As was shown in the video, the hose connection to the siphon break had a... Read more

I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

Replaced mounting stem and tub bearings Read more

It took me about 2 hours to take everything apart and get it back together & running again with no problems. All the parts I ordered were exactly what I needed to fix everything. Thank you all !!! Read more

First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more

Removed front and top panels of washer, removed old switch assembly. Then mounted and hooked up new switch assembly, put panels back on, turned on power and unit now works fine. Thanks for the quick delivery on the part...our total machine down time was only 36 hours. Biggest difficulty was getting the machine out of its position to work on it! Read more

We ordered parts from appliance parts pros and I fixed it. Read more

Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more

Took the front panel off (the door front), disconnected the connector to the door switch and used a wooden clothespin to bypass the door switch. Turned on the dryer to locate loud squeaking sound and found it was coming from the motor area. When I started to take the blower section apart from the motor, that is when I saw the "blower wheel" slipped off the motor shaft. The blower wheel has a "C" clip retainer and compression ring to keep it snug on the motor shaft (but it was loose). Now I... Read more

• Shakes and moves

New leveler pads Read more

I bought the $6.00 plastic clip that holds the agitator In place while washing and the $10.50 spanner wrench that takes the 2 top nuts off to get to the agitator stem the other tools necessary for the job which are just a couple of things I already had then watched the video on line of how to do the job and then did it the whole thing took about 2 hours plus I took my time and gave both tubs a very good cleaning. I paid a guy $400.00 9 months earlier to do the same job wish I hadn't, should... Read more