Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Idler Shaft Washer is an OEM part for Whirlpool dryers. This small but essential component fits on the idler pulley shaft, playing a crucial role in maintaining the alignment and tension of the dryer belt.
Symptoms of a bad Idler Shaft Washer include:
Causes of a bad idler shaft washer can include wear and tear from regular use, loss of material integrity leading to thinning or breaking, or improper installation that may cause misalignment and increased friction.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
I replaced drum rollers, axle shafts and front bearing kit. Still had noise. Ordered Idler Arm, Belt Tension Pulley & Washers. I ordered parts at 3:30 pm on a Wednesday, received new parts at 11:30 am Thursday. The instructions & videos were very simple to follow and provided excellent tips. Back up and running with silence in an 1/2 hour. My 13 year old dryer is running like new again. Way cheaper than calling a repairman. Read more
The Drum Felt Seal is an OEM part for Whirlpool electric and gas dryers. Located between the drum and front panel, this multi-layered seal helps prevent lint buildup and moisture escape during cycles.
Causes of a bad dryer drum felt seal can include cracking, flaking or separation of felt layers from age. Oil or other residue trapped in the fibers can also degrade sealing efficiency.
Symptoms of a bad dryer drum felt seal include:
This genuine Whirlpool OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Started my Maytag dryer (model LDE8200ACW) with a large load early Saturday morning and immediately heard a noticeable thumping noise as the drum turned. Opened the door and checked to make sure some of the laundry hadn’t wadded up and was causing the thumping. Restarted it but the thumping was still present. Did a google search for obvious possible causes for the symptoms but the only suggestion that made sense was to check and make sure the dryer wasn’t rocking on its feet. Checked and found... Read more
The Cycling Thermostat is an OEM part for Whirlpool dryers. It regulates and monitors the temperature inside the dryer during the drying cycle. It ensures that the dryer doesn't overheat and prevents potential damage to clothes or the dryer itself.
Causes of a faulty cycling thermostat can include wear and tear over time, electrical issues, or sensor malfunction.
Symptoms of a bad cycling thermostat may include:
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more
The Idler Arm Sleeve is an OEM replacement part specific to Whirlpool brand clothes dryers. It is a cylindrical component that protects the idler arm and accommodates its movement. Located near the dryer drum, the idler arm sleeve aids in the smooth operation of the drive system that rotates the drum. Causes of a worn idler arm sleeve include normal abrasion from repeated use and vibration. Failure results in increased friction and noise. Symptoms of a faulty sleeve are:
This part is also compatible with Whirlpool, Maytag, KitchenAid, and other brands.
I replaced the motor and all other moving components along with the felt drum seals.drum glides and drive belt. The wiring instruction is where i had the most problems. Because my wiring had only 4 wires in the harness not 5, and one was a different color then the instructions call out, I believe was because it might have been and older model. the instruction called for a gray wire but mine was white with a blue piggy back wire attached. but after finding a few videos on line i figured that the... Read more
The Fiber Washer is an OEM part for Whirlpool appliances. This washer provides a reliable seal and is used in various connections within the appliance to prevent leaks and ensure secure fittings. Its fiber construction offers durability and resistance to wear, making it ideal for maintaining tight seals in high-pressure or high-temperature environments.
Common causes of a bad fiber washer include degradation from water or chemical exposure, physical damage from over-tightening, and natural wear and tear.
Symptoms of a bad fiber washer include:
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more
The Idler Arm Pulley is an OEM part for Frigidaire dryers. This part keeps the belt aligned and tight, preventing slippage and contributing to consistent drum rotation.
Causes of a bad Idler Arm Pulley can range from normal wear and tear, which can degrade the pulley's material or bearings, to improper alignment that puts undue stress on the pulley, leading to premature failure.
Symptoms of a malfunctioning Idler Arm Pulley include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
The very easy diagnosis was motor seizure. Because the machine is about a decade old, I decided to renovate most of the guts. My DIY project included replacing the motor, blower, drum bearing, belt, and door hinge. The end result is a functional dryer with no left-over parts. Lack of parts and hardware challenged the effort. For example, the blower assembly did not have the slide capture for the motor. I had to use the old one which is showing its age. With the exception of the drum... Read more
The Rear Drum Support Shaft is an OEM part for Frigidaire dryers, specifically designed to ensure the stability and smooth rotation of the dryer drum. This component plays a pivotal role in the dryer's operation by supporting the rear of the drum, allowing it to turn evenly and quietly during cycles. Note: The rear drum bearing kit is 5303281153.
The causes behind these issues often stem from normal wear and tear, excessive loads that strain the dryer's components, or lack of regular maintenance. Over time, the support shaft can wear down, become loose, or even corrode, leading to operational inefficiencies and potential damage to the dryer.
Symptoms of a failing Rear Drum Support Shaft include:
The dryer is a Kenmore Laundry Center, model 417-99570150. Bought in 1998, so it is an older model. Not wanting to buy the newer ones that are out now. We opted to fix the Kenmore. Just believe the older models are worth fixing, if at all possible. Frist we had to figure out what parts we would need and if the cost would be worth our time. I went on YouTube: and type in Kenmore dryer not turning on. Watched several videos to narrow down the possible problem. Next step was to... Read more
The Idler Shaft Retaining Ring is an OEM replacement part for Whirlpool dryers. Also called an "E" ring, it is a sealing gasket positioned between the front and rear housing omponents. Maintaining an airtight seal prevents gas leakage and promotes efficient drying performance.
Causes of a bad retaining ring commonly involve compression loss of the rubber gasket material over many years of heating cycles. Exposure to petroleum-based cleaners may prematurely deteriorate the seal as well.
Symptoms of a failed 'E' ring include:
This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore gas dryer models.
First replaced the drum rollers...that wasn't it..took dryer back apart and spun the belt tension wheel by hand (should have done this the first time I took the dryer apart) and it squeaked. so I ordered the full parts: wheel, idler arm, idler spring, arm sleeve, E ring..Put it back together and whoa..no more squealing!! Read more
The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum.
Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.
Symptoms of a bad seal include:
This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more
The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets
Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.
Symptoms of a bad high temperature adhesive include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more
The Idler Pulley Arm is an OEM component specifically designed for Whirlpool brand clothes dryers. It pivots to lift belt tension and remove slack during dryer tumbling.
Symptoms of a problematic idler pulley arm include:
Potential causes involve typical wear from extended usage. Seizing bushings or restrictive movement may diminish functionality over time as well.
This genuine OEM Whirlpool part is compatible with models including some brands produced by KitchenAid, Maytag, and Kenmore.
I removed the front panel of the dryer by removing 2 screws and lifting it up and out. Then I removed 4 screws from the bracket holding the tub in place. I had previously removed the 4 screws from the rear inspection cover so I reached in and released the spring loaded belt that turns the tub and then removed the idler pulley wheel. The tub just lifts out at that point, exposing the 2 Drum support rollers in the rear. I removed the 2 rear drum support rollers and decided to order 2 of... Read more
The Clamp is an OEM part for Whirlpool dryers. This clamp ensures tight and secure connections within the dryer, particularly in securing ducts and vents that are essential for proper airflow and operation.
Clamps may need replacement due to loss of tension, corrosion, or damage from regular use. A compromised clamp can lead to operational issues such as prolonged drying times or excessive noise, resulting from loose parts or improper ventilation.
Symptoms of a bad Clamp include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Our Maytag gas clothes dryer was not drying like it should/used to and was making a lot of noise. After researching online I figured the vent was partially blocked and/or the blower wheel was bad. When I took it apart, the vent had very little lint in the lower elbow exiting the back of the dryer but the blower wheel was loose on the shaft and was missing the clamp. I cleaned out the vent and put a hose clamp on the blower wheel to tighten it to the shaft and tried it again. The noise was... Read more
The High Temp Lubricant Tube is an OEM part for Frigidaire appliances, specifically designed to withstand and operate under high temperature conditions. This lubricant is essential for the proper maintenance and functionality of various Frigidaire appliances, offering protection against heat and friction.
Over time, the lubricant can degrade or become contaminated, which can compromise its effectiveness. Causes of a bad high temp lubricant include exposure to extreme temperatures, accumulation of dirt and debris, or simply the natural breakdown of the lubricant over prolonged use.
Symptoms of needing a new High Temp Lubricant Tube include:
Replaced the rear drum bearing assembly and the front top felt that the drum rides on and since I has it apart installed a new belt. Simple to do and takes very little time! Read more
The Thermal Fuse is an OEM part for Whirlpool dryers. This safety device protects the dryer from overheating by cutting off power if the dryer exceeds a certain temperature. It is crucial for maintaining safe operation and preventing potential fire hazards. This thermal fuse has 1/4-inch terminals and operates around 243 degrees F.
Causes of a bad thermal fuse include lint buildup causing overheating, blocked ventilation, or a malfunctioning thermostat. These issues can lead to the fuse blowing to prevent further damage or risk.
Symptoms of a bad thermal fuse include:
Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more
The Door Strike is an OEM part for Frigidaire dryers. It is a small, essential component that ensures the dryer door remains securely closed during operation. The door strike engages with the door catch to keep the door latched, allowing the dryer to operate efficiently and safely. Without a functioning door strike, the dryer may not start, or it could stop mid-cycle.
You should replace this door strike if it becomes damaged or worn out. Over time, the door strike can suffer from wear due to regular use, misalignment, or accidental impact, leading to issues with the dryer door latching properly.
Symptoms of a bad door strike include:
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch. I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to... Read more
The Door Catch Kit is an OEM part for Whirlpool dryers. It includes the door catch and the necessary mounting hardware to secure it in place. This kit ensures the dryer door remains securely closed during operation, preventing heat loss and ensuring the appliance functions efficiently.
Causes of a bad door catch include regular wear and tear, physical damage, or misalignment of the door, which can impact the catch's ability to latch properly.
Symptoms of a bad door catch include:
Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more