Mmv1680ws1 Parts

Knowing the odds of 2 failures occurring at the same exact time was unusually high, I just searched your site for what other broken items might affect these two failures. Came up with next control item upstream and tallied that item failure with percentages of successful repairs, (4 mins.) door safety switch. Since I had to change out the most likely of the 3 and since I was already was going to be into the switch panel I ordered all 3 and swapped them all out to cover my butt, as they were... Read more

Well, I gotta say I was happy to find you still had parts for almost 20 year old microwaves. The microwave itself worked fine, so I hated to have to buy a new one, but I just couldn't take being hit in the head anymore; and my fix of using string and wire to tie it to the surrounding cabinets was unsightly to say the least. I'm glad I did some research and found this part - all I had to do was pop it in place and now the vent grill is secure. Problem solved with minimal cost. Read more

Checked switch with a voltmeter, determined the switch was bad. Ordered a new switch....watched a short how to you-tube video.....and from there.....it was fixed. Read more

• Noisy
• Tray won't turn

Removed 8 screws from bottom panel on microwave. Pulled two prong plug off old motor. Read supplied voltage off motor decal and tested for it. Deemed motor to be bad and changed it. Works great. After tearing old motor apart it seems a liquid got in there from inside microwave. No seal on motor. Bad design flaw in my opinion. Read more

I got it in the mail, I opened it, I handed it to my wife....and she installed it. Easy-Peasy! (Being retired is a blast) Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

• No heat

I am not an appliance repair man. I am a general surgeon. I went online and researched the problem. The consensus was that my magnetron and diode were the most likely culprits. To replace my microwave with a comparable model would have cost at least $800. The diode and magnetron cost around $170. I watched a few videos on YouTube demonstrating how to do the repair safely and I felt like I could do it. I ordered the parts on a Monday evening and had them Wednesday. The only difficult part of... Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

Easy to replace Read more

New vent grille arrived in 2 days - installed with 2 screws - very straightforward - done! Read more

Replaced vent using a philips screwdriver; simple! Read more

Careful placement of new screws into the inside of the outer door that now hold the frame assembly to the door secured the frame assembly to the outer door. All of the other parts I bought and replaced were a waste of money. I figured since I had them I might as well install them anyways. Easier than sending them back since I had the whole thing apart anyways. The part I really needed was no longer available, the outside door. The glass reinstalled into the retainers in the door without a... Read more

When the new bulb didn't want to go in, I felt around and realized the base of the old bulb was still in there. With some effort I got it out and new bulb in, Light cover fit fine, but did not come with a screw to hold it in. That would have been helpful. Read more

We just popped the replacement parts in. By the way, Sears that sells the Kenmore, the make of our microwave, didn't have the parts we needed online. I was very pleased with my Chat experience with RobinC from your website. She located the parts I needed and even arranged the payment. Great service! Read more

• Won't start

First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more