Mvwx700xwl Parts

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more

Rebalanced the load but noticed the drum was sitting lower and the springs were wore out and it went out of balance easy, so i got the suspension rod kit and installed it and it works much better. It took me 2 hours because i didnt have adequate room to move around. Hour job if you have room. Read more

I pulled the old washer plate out and then replaced it with the new one. No problems, and working like a new one again. Read more

Removed valve and replaced with new one. Read more

Touch up paint Read more

Replaced It With New One Read more

I had previously replaced the transmission in my two year old Whirlpool Cabrio washing machine. Overall it was in good shape but gets heavy use. That repair was approximately $200 and worked for several months. Recently it began leaking. At first I thought it was the tub-to-shaft seal. I replaced this part but it was still leaking. It turns out it was the simplest of things... The drain hose was not connected very well! I replaced the drain hose ($11 part) and while I was at it I... Read more

I had to cut the old agitator out with an oscillating saw in order to access the agitator drive. This is the second Maytag (MVWC 565) I have had to do this to. I first tried removing it by sliding straps under the agitator then then using a jack to pull it loose which did not work either time. One suggestion I have would be to remove debris from tub as you cut in order to prevent it from dropping from the inner tub into the outer tub. Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more

My Mom's Kenmore had a burnt plastic smell after a thunderstorm. Found motor capacitor had melted through, dumping liquid platic "spaghetti" onto the insulation blanket under the washer. All other compents looked fine. Told her not to use it until I replaced capacitor. The washer is 4 yrs old but the new capacitor revision was 3 letters higher, so they've made some design changes. Externally it looks the same. There is a large number on the capacitor, but the part is ordered by the much... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

There was a horrible screeching noise coming from the washer, and upon inspection I found that the retaining nut that attaches the cam to the machine was either improperly tightened to begin with or had worked itself loose causing the cam to wobble and the belt to work down the cam. The cam gear teeth became worn and the belt worked itself half off the cam and cut a hole in the protective plastic screen containing the whole ensemble. I purchased the belt, shield and cam kit. The parts are... Read more

Removed the screws, lifted the old lid out of the hinges. Replaced the hinges, set new lid in the hinges and replaced screws. Read more

Remove the two valves at back of washer, only 4 screws, remove the electrical clamps, replace with valves, easy, 20 minutes to fix, and a woman did it, saved $320.00, yahoo Read more

• Leaking

Took off cover, installed new parts. Read more