She33t52uc/02 Parts

• Will not dispense detergent

Process was a bit more complicated than the videos I had watched online. Had to remove both front panel and control panel to get to soap dispenser. Removed wires to soap dispenser and rinse aide dispenser. Removed wire "harness" around the top and right side of dispenser. Pried back the clips to allow dispenser to be pushed out. It was helpful to have another person to hold the door open at this point. Bent clips back and reinstalled everything. New part works great. Read more

Replaced dispenser Read more

I only needed a flat head screwdriver to remove the clips holding the parts in. It took all of 10 minutes and the dish washer is running great now. Read more

I bought just the replacement lid based on other reviews. The door cost about a third of the whole soap dispenser module but took a chance it was just the lid. Although the part number is the same there was a new flange on the inside of the lid. Would have been nice if Bosch sent the redesigned part to owners. Either way replacement took 2 minutes and the problem is gone Read more

Bought new wheel and the are easy to replace. Found why the brok and did a quick fix so it wont happen again. As the wheels age one will pull off then they all get weak and the rack will come off the track, To prevent this. you can put a plastic tie so the wheels cant fall off in the first place, The disign holds them in place with pressure from the plastic but the plastic ages and gets weak. A tie would have to actually break before the wheel can fall off. Read more

I only needed a flat head screwdriver to remove the clips holding the parts in. It took all of 10 minutes and the dish washer is running great now. Read more

"Watertap" E15 error code indicated leaking. Dried it all out to allow it to run again. Ran dishwasher with front and bottom panels off to get a visual on leak causing the styrofoam float to set off the code. Saw it was coming from the diverter area. Ordered this assembly -- which DOES include the seal ring, by the way -- pulled dishwasher all the way out to replace it, and VOILA. No more leaking or error code. (This took a few days to analyze and receive the part, so in the meantime we... Read more

I only needed a flat head screwdriver to remove the clips holding the parts in. It took all of 10 minutes and the dish washer is running great now. Read more

• lights flashing or blinking
• Will not drain
• Noisy

Water was left in the bottom of the dishwasher after each time we ran it and the dishes were no longer getting clean. Also, there was always soap left in the dispenser. I took the DW completely apart and determined the water was not being forced out of the discharge tube and was merely draining via gravity. I ordered a replacement drain pump and removed the entire motor/pump assembly from under the DW. Once the pump was replaced and the DW was put back together, the water now was forced out... Read more

I went on your very user friendly website and looked up my bosch dishwasher. I love your diagrams and I felt confident that I could figure out what we possibly needed to get the door to close correctly and get the washer back working again. Your staff is courteous, service was fast and I would definitely recommend Appliance Parts Pros. Read more

Got new replacement spring and cord for our Bosch compact dishwasher. A plastic retaining bracket that held the old spring also was broke but the new spring had its own piece that fit into a slot in the plastic frame, so i just popped it in there, connected the cord, and bingo. The door now works. I tried using the old spring, but it would not work because of the broke bracket. Read more

I went on your very user friendly website and looked up my bosch dishwasher. I love your diagrams and I felt confident that I could figure out what we possibly needed to get the door to close correctly and get the washer back working again. Your staff is courteous, service was fast and I would definitely recommend Appliance Parts Pros. Read more

Leak was slow but becoming gradually worse. Pulled dishwasher out from under counter then visually inspected sump while it ran. As soon as the water got very hot, I could see the sump leaking where it meets the stainless pan. Searched for the correct sump gasket without success. Turns out that the gasket is built into the sump for this model. The built-in gasket is very narrow (under-engineered IMHO which is probably why it developed a leak). Thanks to Simon's excellent videos at... Read more

It finally gave E15 code, then after drying out the E15 code came back within 5 minutes of running. I dried out the base then I ran the dishwasher and observed water coming down the overflow chute after running only 5 minutes.There is a water inlet (clear water chamber on the side of the machine). It had some gunk inside that was stopping a black float shut-off from moving. I replaced the water inlet chamber. I also suspected the non return valve (also called a check valve). From the parts... Read more

Leak was slow but becoming gradually worse. Pulled dishwasher out from under counter then visually inspected sump while it ran. As soon as the water got very hot, I could see the sump leaking where it meets the stainless pan. Searched for the correct sump gasket without success. Turns out that the gasket is built into the sump for this model. The built-in gasket is very narrow (under-engineered IMHO which is probably why it developed a leak). Thanks to Simon's excellent videos at... Read more

Leak was slow but becoming gradually worse. Pulled dishwasher out from under counter then visually inspected sump while it ran. As soon as the water got very hot, I could see the sump leaking where it meets the stainless pan. Searched for the correct sump gasket without success. Turns out that the gasket is built into the sump for this model. The built-in gasket is very narrow (under-engineered IMHO which is probably why it developed a leak). Thanks to Simon's excellent videos at... Read more