Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix excessive vibration and loud spinning noise in your washer. Balance ring assembly stabilizes the drum during spin cycles. Advanced DIY repair.
With all the bouncing around the shocks appeared to be done in but that was not the issue. The key was the balance ring. It had leaked all the fluid out causing all the beads to clump. This caused the drum to wobble wildly and not spin at speed. Getting to the ring to replace it is not a trivial task and took me several hours. Would have been much easier with help as the drum is quite heavy. The on-line video's are very handy and should be watched before attempting this job to save you a... Read more
Fix water leaks from your washer's drain system. This drain hose assembly channels wastewater properly. Easy DIY repair with back panel removal.
This is an easy fix. Just remove the back panel, remove the hose clamp to pull out the old hose, put the new hose on, make sure the clamp is well centered onto the connection, and return the back panel. Make sure to insert the drain hose into the three plastic guides that prevent the hose from moving around. The Samsung factory did not do this on my original hose, which is why it failed, because it was rubbing against the tub support and it wore a hole into the hose. I am going to complain... Read more
Fix a washer that won't fill with water or leaks onto the floor. This water inlet valve controls water flow into your machine. DIY repair in 10 minutes.
The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more
Secures your washer's door boot seal to prevent water leaks. Replace if you notice leaking during cycles or a loose seal. Confirm fit with your model.
I ordered new door gasket, front and rear clamp for gasket and installed them. Read more
Fix tE error codes with a new water temperature thermistor. This sensor monitors wash water temp. DIY-friendly repair takes under 10 minutes.
I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more
Replace your washer's door boot seal when you notice water leaks, mold, or visible tears. Ensures a watertight seal during wash cycles. Verify fit by model.
The Washer Door Lock Bezel Cover-Switch Assembly is an essential component for maintaining the functionality and security of your Samsung washer. This genuine OEM part ensures a perfect fit and reliable performance, matching the original design of your appliance. The assembly combines both the bezel cover and the switch, providing a seamless replacement that restores the door locking mechanism to its optimal state. By choosing this Washer Door Lock Bezel Cover-Switch Assembly, you benefit from enhanced durability and precise operation, preventing issues such as door leaks or malfunctioning locks. Installation is straightforward, allowing you to easily replace a damaged or worn-out part without the need for professional assistance. Compatible with a wide range of Samsung washer models, this genuine OEM part guarantees compatibility and longevity. Investing in this high-quality assembly helps maintain your washerGÇÖs efficiency and extends its lifespan, ensuring that your appliance continues to deliver excellent washing performance. Trust in this reliable component to keep your washer running smoothly and securely.
Ordered part by looking at parts diagram and followed You tube instructions. Easy and quick! Read more
Fix water leaks behind the detergent drawer with this washer upper nozzle connector. Located under the top panel. Easy 5-minute DIY repair with basic tools.
When I opened the rear cover and check the temperature sensor, I noticed the wire connection was damp. I dried it up with a hair dryer and it worked again for a few days. Then the problem came back. When I gone back to inspect the second time, i noticed a lot of water on the floor. I knew there was a leak. I followed the disassemble samsung washer video from "Repair clinic.com" to open the top cover, then i realized the assembly hose was busted. I ordered the parts from this site and... Read more
Fix ND error codes and drainage issues with this washer check valve. Prevents backward water flow in drain pump. DIY-friendly repair with video guide.
Washer said error no drain. Cleaned the filter and still no drain. So the next step was to check the hose for any debris and when I went to pull the hose off it broke, at the same time I found the check valve flap broke in the drain pump and it was blocking the hose. So I replaced the check valve on the drain pump and replaced the hose. Read more
Washer won't start or door won't open? A faulty door lock assembly is the likely cause. This repair takes about 15 minutes with basic tools.
Ordered part took seal off to gain access..couple of screws and connectors..bk in business Read more
Fix leaks or mold buildup with a new washer drain hose. Channels water away from the drum. Moderate DIY repair—requires back panel removal.
Bought and installed a new drain hose. It required removing the back access panel and loosening a pinch clamp that holds the hose on its male outlet end, and threading the hose out the back of the washer. Read more
The washer motor rotor assembly is the outer rotating component of a direct-drive washer motor that works with the stator to generate the electromagnetic force that spins the wash basket. It is a core part of the motor system that drives both the wash and spin cycles. Replace this part if your washer won't spin or agitate, makes a loud grinding or humming noise during a cycle, or if the machine shakes excessively during operation.
Actually, I am returning your parts. THERE IS NOTHING WRONG WITH THEM! My wife actually found out that we had a warranty on our washer that we didn't know about. But, I can comment that I did chat with your customer service and you guys were very helpful. Read more
The Washer Liquid Soap Dispenser Tray is an essential component for maintaining the efficiency of your Samsung washer. This genuine OEM part is specifically designed to hold and dispense liquid detergent accurately, ensuring that each laundry cycle receives the right amount of soap for optimal cleaning performance. Crafted with durability in mind, the dispenser tray withstands regular use and resists cracking or leaking, providing a long-lasting solution for your appliance. Installing the Washer Liquid Soap Dispenser Tray is straightforward, making it an ideal choice for DIY repairs. Its precise fit guarantees seamless integration with your Samsung washer, restoring the functionality of the liquid soap dispensing system without any complications. By replacing a damaged or malfunctioning tray with this genuine OEM part, you enhance the overall performance of your washer and extend its lifespan. Compatible with a variety of Samsung washer models, this liquid soap tray offers reliable and consistent detergent delivery, helping you achieve cleaner, fresher laundry with every wash. Choose the Washer Liquid Soap Dispenser Tray for a dependable and efficient solution to keep your washer operating smoothly.
Replaced with new Detergent cup and fill cap. Cup symphony perfectly. Simple fix for frustrating problem. Read more
Fix a washer stuck mid-cycle or showing overfill errors with a new water level pressure switch. This part detects water levels to control fill cycles.
Machine was a front load washer, after doing some research found that problem is usually caused by pressure sensor or the spider arm which attaches motor to tub. Read more
The Refrigerator Screw-Tapping is an essential component for maintaining your Samsung refrigerator's functionality. This genuine OEM part ensures precise threading, allowing screws to be securely fastened without damaging the surrounding materials. Designed specifically for Samsung refrigerators, it guarantees a perfect fit and reliable performance. Whether you are replacing a damaged screw-tapping or performing a repair, this Refrigerator Screw-Tapping simplifies the process, saving you time and effort. Its high-quality construction provides durability and long-lasting support for your appliance. By choosing the Refrigerator Screw-Tapping , you ensure your refrigerator remains sturdy and functional, enhancing its overall lifespan. This genuine OEM part is easy to install and seamlessly integrates with your existing setup, making it an ideal choice for DIY repairs. Trust in the quality and compatibility of this Samsung part to keep your refrigerator operating smoothly and efficiently.
The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more
Supports the drum and absorbs vibrations to reduce noise and prevent walking during spin cycles. Replace if washer is unbalanced or excessively noisy.
Replaced all four shocks and both springs. Read more