Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a refrigerator that won't cool or has freezing issues. This main control board regulates temperature and system cycles. Moderate DIY repair.
This was a newer GE Monogram side-by-side unit that used an inverter compressor. I removed the inverter and used an ohmmeter to measure the resistance of each of the three windings. They were all very close to one another: about 6.8 ohms per winding. I concluded that the compressor was probably not at fault. The inverter kind of burned or chemical-ish, and, when opened, showed an electrolytic capacitor had burst. I replaced the inverter with an overnight part from Amazon. It was the same... Read more
Fix a refrigerator that won't cool or has temperature issues. This main control board manages cooling cycles, fans, and compressor operation. Moderate DIY.
Replaced the Main Control Board Assembly along with the evaporator and condenser fan motors. I thoroughly cleaned the very very dirty condenser with a 4$ brush offered by the parts specialist and while I was at it, I changed the door seals and replaced one of the door trays. Beats the crap out of spending $10,000 on a new refrigerator that because of Covid 19 wouldn't be here before the middle of November. Thank you Matt for your help! Read more
The Spring Closure is an OEM part for GE refrigerators. This spring aids in the automatic closing of the refrigerator door, ensuring it seals tightly after each use to maintain optimal internal temperatures.
Causes of a bad spring closure can include regular wear and tear, corrosion due to moisture, or accidental damage that compromises its function.
Symptoms of a bad spring closure include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
1) Remove toe kick panel - 2 Philips head screws 2) Lay down on floor. This might be the hardest part of the repair from some people! 3) Remove broken spring, no tool required. 4) Using your fingers, slip one end of new spring into hole on lever arm. (If you're not sure how it should go, look at the spring on the other door, assuming you have a side-by-side.) 5) Hook the other end of the spring around a round-shank screwdriver. (Don't even bother with pliers. You will disregard this advice... Read more
This halogen light bulb restores bright, reliable illumination inside your appliance, making it easier to check food and read controls. Replace a burned-out or broken lamp to bring back safe, convenient visibility while cooking.
Had to remove all three food drawers and the back panel behind the drawers (4 screws). The water tank comes with the associated tubing which would typically require access to the back of the fridge to run the new lines. Instead I clipped the existing lines inside the fridge. Then I clipped the lines off the new tank so they would line up with the old lines. I then used a 5/16" OD compression coupling (Lowes or Home Depot) to connect the ends of the tubing together. The joined tubes are... Read more
Stores and supplies water to ice maker and dispenser. Replace if cracked from freezing, leaking at seals, or broken from impact. Includes tubing.
Fix food freezing or warm spots in your fridge with a new air damper assembly. Controls airflow between compartments. Moderate DIY repair, 1-2 hours.
It started with clicking sounds for about 10 seconds at random times throughout the day. eventually the clicking sounds were gone and the temperature in the fresh food section was dropping below freezing. Turns out that one of the 3 damper doors was stuck open. My fridge has a damper door in the top left and 2 doors in the bottom left. One of the bottom doors was dedicated to the quick chill drawer which hadn't worked in some time. but since the quick chill door was stuck closed it did not... Read more
Replace your worn refrigerator door gasket to restore an airtight seal, maintain consistent cooling, and reduce frost buildup. Verify fit with your model.
This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.
Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more
Door gasket and label assembly creates an airtight seal to keep cold air in and moisture out. Replace when worn or damaged to restore efficiency. Verify fit.
Verified the dampers actuated and evaporator fan wasn't blocked. Replaced both door gaskets per tech manual guidance. The Freezer one came yesterday...still waiting on the fresh food one. Freezer one went on fine -- just a little challenge aligning the bottom, but got it after only a small bit of frustration. It has already helped fix the situation it seems. But I will go ahead and replace the fresh food one when it gets here, as it's kinda nasty anyway. Be sure to soak the gasket in hot... Read more
Magnetic door gasket seals the refrigerator compartment to maintain temperature and reduce energy loss. Replace when worn, cracked, or loose. Confirm fit by model.
Removed and replace seals. Service video has you removing the doors. I found this to be unnecessary. Read more
Fix a refrigerator that won't cool, beeps constantly, or has no power to the compressor by replacing the main control board. Moderate DIY repair.
EVERY THING WORKS, PUT IN NEW CONTROL BOARD AND WATER VALVE. VERY PLEASED. Read more
Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.
Common theme on the blogs was thermistors and or defrost heater/thermostat. Ran self-diagnostics which turned on defrost heater which was fine. All five thermistors indicated ok on diagnostic also, but I read more than one time "replace the thermistors no matter what if your FF section isn't cooling". So I ordered all five thermistors and defrost limiter thermostat. Received all in 48 hours (great shipping service), took me about three hours to replace all thermistors and thermostat just as... Read more
Creates an airtight seal to keep cold air in. Replace if torn, warped, or leaking to restore proper sealing and temperature control. Confirm fit by model.
Fix ice buildup on evaporator coils with this defrost thermostat. Monitors coil temperature to signal defrost cycles. Test for continuity when frozen.
Refrigerator freezing food or not cooling properly? The air damper controls cold air flow from freezer to fresh food section. DIY-friendly repair.
Took out old damper which had a broken flap door. Put in the new damper and fridge worked good as new. Read more
Fix a refrigerator that won't start or clicks repeatedly. This compressor capacitor stores energy to start the motor. DIY repair typically takes 30 minutes.
Replaced overload, and capacitor Read more