Push Button Start Switch Parts

• Won't start

All I had to do was remove 3, 1/4" screws from the back and take the front off. Two 5/16th screws hold the circuit board in place, remove them and press the button into the hole from the back. Replace the circuit board, slide the front back on and install the three 1/4" screws. Always unplug the washer first! Read more

Checked the three door switches; used ohm meter to see if there was resistance or if a switch was bad. 2 out of 3 switches showed resistance with the ohm meter. The last one tested (of course the last one) NO (normally open) did not show resistance; I.e. the ohm meter reading did not change when the switch was depressed. Appliance parts pros was the only company that had the same model number I was looking for (SZW-V16-FD-63). I ordered the relay switch, 2 days later it arrived (regular... Read more

• shuts off after a few seconds

I did some searching on the internet to see if others had the same issue I was having. There were many who had the same problem and everyone of them fixed it by changing out the latch switches, which in my case, were part of the latch body assembly. So I ordered the part from AppliancePartPros and it arrived on Tuesday, 2 business days after I ordered it, which was just as expected. I had also done some research regarding how to replace the latch body assembly and, although I couldn't find... Read more

I bought the replacement knobs from Appliance Parts Pros.com and they were much better knobs that what originally came with the unit. They are actually metal and the plastic posts that connect with the range are a much higher grade plastic. To be honest I think the stove works better than it did when it was new. Some of the original knobs may have been broken when we purchased the unit. Replacement took under 5 minutes for all of the knob. Oh....and by the way....they appear to be the same... Read more

• Light not working

• Will not fill with water

Replacing the inlet valve solved the problem. The old valve was somehow clogged with white sediment. I probably could have taken it off and cleaned it out if I'd known, but replacing the valve was much easier. Took about half an hour to repair. Video walk through was extremely helpful. Great to have a working dishwasher again! Read more

Had to buy two more to replace it probably in due time will have to replace others so sad that it is made so cheap. Spend so much for a cooktop and only had it for a year and already had to replace something GE profile Read more

Replacing the bad harness switches with the new set fixed the problem. Read more

Pop out the old switches with a putty knife pressing down on the tab, grabbed with pliers to pull out, disconnect the wires and connect new switches, pressing back in place. Read more

I went online, ordered the part and installed it,,, took 15 minutes to install,,,saved huge $$$ easy peasy!! :-) Read more

• Won't start
• Element will not heat

First, I just unscrewed all nuts that are holding the frame and all surface elements. Once all parts, surface elements, control switches, are loose from the original glass, I just moved all parts to the new glass. Due to the weight of the glass, all actions have to be done carefully as I broken one corner of the glass couple of years ago when I replaced one of the control switch. Read more

First, I modified old butter knife by bending a 90° angle about 3/4" from the tip. I slid the bent in up under the bottom of the switch cover and worked it to one side. I then rotated the knife downward using the bent end to pry the cover off. The switch is held by plastic arms on each side. The bottom right arm has a locating pin that fits into the switch. Unplugged the switch and re-installed. Read more

• Element will not heat

We cut the power, took the control panel off, got the burner switch number from the original part, and ordered a new one. We were a little worried at that point, because your website offered a "replacement" part, with a different number than the original. However, we put the model number into your double check feature and were assured that we were getting the right part. The part arrived in two days and frankly we were still worried, because the new part was slightly larger than the original.... Read more

New knobs Read more

• overflowing
• Will not fill with water

I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle. Read more

• Will not fill with water
• Will not stop filling with water

Hmm...watched video after reading on web of running water problem with GE washer....common fail .....moving stuff to get to the washer took all the time, easy fix but a lot of screws to remove and looking time APP site very good, will order again if need be thanks Read more